Kohler KD62V12 Operation And Maintenance Manual Download Page 89

Page: 89 / 210

Maintenance

Inspection and maintenance schedules

Task iden

tification

Component

Schedule

Service

Type

Task description

Time limit (h)

Calendar limit (y

ear)

eplacemen

erhaul

Inspection/Clean R

epair

/Adjus

tmen

SL120

Coolant sampling

Check coolant quality.

(For more information see:

5.10.1 Collecting coolant sample — SL120,

page 123.)

SL122

Recommended:

First 250 service

hours for a new or

overhauled engine

250

Engine oil replacement.

(For more information see:

5.9.6 Changing engine oil — SL101, SL121,

page 118.)

Oil filters and oil filters for cooling jet replacement.

(For more information see: 5.9.4 Changing oil filters

— SL101, page 113.)

It is recommended to check the engine oil charac‐

teristics at the same time.

(For more information

see: 5.9.1 Collecting and analyzing oil sample —

SL100, page 111.)

Perform all check before starting and perform a

test run.

Without centrifugal oil filter

SL101

Engine oil filters

standard

250

Replace filters. Clean the seal area before removal

the old filter to prevent oil contamination.

(For more

information see: 5.9.4 Changing oil filters — SL101,

page 113.)

SL121

Engine oil change

with engine oil

“Category 2”

250

Oil change maximum interval. Note: Replace engine

oil at least every 2 years. Final engine oil interval

depends on exchange interval factor according to

engine oil category and fuel sulfur rate. 0<fuel

sulfur rate<0.5%: the factor is 1 (no change on the

engine oil change interval). 0.5<fuel Sulfur rate<1%:

the factor is 1/2 (reduce by 2 times the engine oil

change interval and use only engine oil category 2

or 3). 1<fuel sulfur rate <1.5%: requires additional

approval. No oil Category 1 in case of K175.

(For

more information see: 5.9.6 Changing engine oil —

SL101, SL121, page 118.)

Engine oil change

with engine oil

“Category 3”

500

With centrifugal oil filter

SL101

Engine oil filters

standard

500

Replace filters. Clean the seal area before removal

the old filter to prevent oil contamination.

(For more

information see: 5.9.4 Changing oil filters — SL101,

page 113.)

KD62V12 33521030301_8_1 EN_US 2022-09

Summary of Contents for KD62V12












































































































































































































Search results

Summary of Contents for KD62V12

Reviews:

Related manuals for KD62V12

Brands by name

Popular brands

Kohler KD62V12, Operation And Maintenance Manual

Search results

Summary of Contents for KD62V12

Reviews:

Related manuals for KD62V12

Brands by name

Popular brands