Kohler KD62V12 Operation And Maintenance Manual Download Page 49

Page: 49 / 210

Safety

Accessible areas

Sign

(ISO 7010)

Description

ISO 7010/W012 – Warning sign - Electricity

Death or serious injury due to electrical shocks!

ISO 7010/W017 – Warning sign - Hot surface

Severe injuries due to hot surfaces!

ISO 7010/W025 – Warning sign - Counterrotating rollers

Severe injuries due to drawing-in movement!

ISO 7010/M002 – Mandatory action sign - Refer to instruction manual/booklet

In order to ensure that all residual risks are known by the personnel, the

system documentation must be read and understood. Make sure that all

residual risks according to the risk assessment are reflected in the system

documentation. Provide documentation to the personnel according to the

“Target audience”.

Tab. 12: Engine area signs requirement

KD62V12 33521030301_8_1 EN_US 2022-09

Summary of Contents for KD62V12












































































































































































































Search results

Summary of Contents for KD62V12

Reviews:

Related manuals for KD62V12

Brands by name

Popular brands

Kohler KD62V12, Operation And Maintenance Manual

Search results

Summary of Contents for KD62V12

Reviews:

Related manuals for KD62V12

Brands by name

Popular brands