1374956-T01-B
-4-
安装前准备
安装前准备工作
1.
预埋排杆口、接线盒、角阀位置
严格按预埋图纸要求施工；如不按要求布局，出现安装不了
等后果，本公司不承担任何责任。
2.
先排掉角阀管道内污水
将角阀管道内污水排干净；确保进入产品的水质符合
GB5749
的市政自来水。
3.
钻膨胀螺栓的孔位
按图纸要求钻膨胀螺栓孔位
Ø10
×
60
。
PREPARATIONS BEFORE INSTALLATION
Preliminary Installation
1. Embed the position of the drain assembly hole, junction
box, angle valve
Construct in strict accordance with the requirements of the
embedment drawing. If the product cannot be installed due
to the disregard for the requirements, we will not assume
any responsibility.
2.
Drain sewage inside the angle valve pipe first
Drain sewage inside the angle valve pipe. Make sure that
the quality of the incoming water is the municipal tap water
complying with GB5749.
3. Drill a hole for the sleeve anchor
Drill a hole (Ø10
×
60) for the sleeve anchor according to
the drawing requirements.
Floor tile position
֪ߡृѹ
Inlet angle valve
position
ࡊઅஂѹ
Embedded junction box
ⷃݎিढ
4-Ø10 hole depth 60
(Drill the hole after
laying the wall tiles)
4-Ø10
ࢋ
60
ͧૉृե۸ͨ
Embedded junction box
ⷃݎিढ
Inlet angle valve position
ࡊઅஂѹ
Required inner
diameter of
drain assembly
hole is Ø40-45
ߔՍӄڬ
ࡌ
Ø40-45
Floor tile position
֪ߡृѹ
ԥӒࡊङⷃॐ۞֣
Embedment Diagram (cold water only)
Embedment Diagram (hot and cold water)
߄Ӓࢽࡊङⷃॐ۞֣
Note: It needs to decide the finish position of floor tiles
ࡨүؔӟ֪ߡृவ؏ۨѹ
Note: It needs to decide the finish position of floor tiles
ࡨүؔӟ֪ߡृவ؏ۨѹ
Required inner
diameter of
drain assembly
hole is Ø40-45
ߔՍӄڬࡌ
Ø40-45
Floor tile position
֪ߡृѹ
Inlet angle valve
position
ࡊઅஂѹ
Embedded junction box
ⷃݎিढ
Floor tile position
֪ߡृѹ
Inlet angle valve position
ࡊઅஂѹ
Embedded junction box
ⷃݎিढ
4-Ø10 hole depth 60
(Drill the hole after
laying the wall tiles)
4-Ø10
ࢋ
60
ͧૉृե۸ͨ
Note: It needs to decide the finish position of floor tiles
ࡨүؔӟ֪ߡृவ؏ۨѹ
Note: It needs to decide the finish position of floor tiles
ࡨүؔӟ֪ߡृவ؏ۨѹ
Required inner
diameter of
drain assembly
hole is Ø40-45
ߔՍӄڬ
ࡌ
Ø40-45
Required inner
diameter of
drain assembly
hole is Ø40-45
ߔՍӄڬ
ࡌ
Ø40-45
