background image

 

Ensure the product is connected to cold water supply, or it may cause body burn or 

machine fault. 

 

The product must be connected to the ground correctly. If not connected to the ground, it 

may cause electric shock. Only use with supplied 3-prong (grounded) electrical plug. 

 

Use only an electrical outlet with leakage switch (rated induced currents below 15mA) or 
insulating transformer (1.5kVA~3kVA) to protect outlet loop. Failure to do so may cause fire 

or electric shock. 

 

Ensure the plug is firmly inserted into the wall outlet at all times, or it may cause fire, heat 

or short circuit. 

 

When removing the plug from wall outlet, remove by holding the plug. Do not pull on the 

cord. 

 

If the power soft wire is broken, cease use immediately and contact Kogan.com for 

replacement or repair. 

 

Turn off the power before doing any general maintenance or spot checks. Nozzle clean will 

require power to check. 

 

People in need of supervision or a guardian (people with disability, children, older people) 

must not be left unattended with the device. 

 

Do not let children play this product. 

 

Do not throw lit cigarettes, matches, or any other flaming material into the toilet. 

 

 

General safety notices: 

 

Do not use the product when it is loosely fitted. The toilet and seat may separate and fall 

off, causing body injury. 

 

If damaged, do not touch broken area. Cease use and contact kogan.com for assistance. 

 

Do not impact forcefully, put heavy weight upon, crouch on, or stand on the product. This 

may cause product damage, personal injury, or indoor water seepage. 

 

Do not use the seat for anything other than what it was designed for. Do not pull the 
product by holding the seat or cover, and do not attempt to sit on it while it is not in 

position. Failure to do so result in product damage or injury. 

 

Use kitchen detergent (neutral) to clean the plastic parts (seat cover, etc) and water inlet 
soft hose. Do not use the following materials: bathroom detergent, house detergent, 
petrol, banana oil, cleaning powder, nylon brushes, etc. These products may damage the 

plastic parts, cause cracks, or may cause water leakage because of damaged soft hose. 

 

To avoid sudden water leakage, do not remove the water inlet filter when angle valve is 
open. Refer to Cleaning & Care section of this user guide. 

 

Do not crush or bend water inlet hose, as it may cause water leakage. 

 

If replacing another bidet, use the new hose supplied with this product. Do not reuse the 

previous hose, as it may cause water leakage. 

 

Do not pour hot water into toilet, as it may cause body injury or indoor water seepage due 

to toilet damage. 

 

Do not flush with large amount of toilet paper or other subjects except sewage and small 
amount toilet paper, as it may cause toilet damage. Do not flush tampons, condoms, or 

sanitary products. 

 

Do not lean on the toilet cover while using, it may damage the seat cover. 

Summary of Contents for KAWNDBIDETB

























Reviews: