Koenic KRVC 2320 RC, User Manual

Page: 21 / 148

21
English
Content
1 x Robot vacuum cleaner with dust container
1 x Charging station with charger
1 x Water tank
2 x Mop cover
1 x Cleaning brush
2 x Side brush sets
2 x Batteries (AAA/LR03)
1 x User manual
1 x Warranty card
Controls and components
A
Shock absorber
B
Exhaust holes
C
Dust container release
D
Dust container
E
On/Standby switch with power LED
F
DC jack, vacuum robot
G
Charging station
H
Charging contacts
I
Charge control LED
J
DC jack, charging station
K
Dust pre-filter and fine filter
L
HEPA filter
M
Filter holder
N
Filter bottom lid
O
Brush roller
P
On/ off switch
Q
Drive wheels
R
Rotary brushes
S
Battery compartment with lid
T
Vacuum cleaner charging contacts
U
Depth sensor
V
Charger with charging cable and DC plug
W
Water tank with mop cover and cap
(not shown)
X
Cleaning brush
Y
Replacement mop cover
Remote control
1
Transmitter diode
2
Vacuuming mode button
3
Button forward
4
Button left
5
Timer button
6
Button charging station
7
Time button
8
Button backward
9
Button right
10
Start / Pause button
11
Mode button
12
Display
Assembly
Charging station
Fig.
1
Insert the DC plug of the charger into
the DC socket on the charging station.
Connect the power adaptor to the
mains.
Fig.
2
Place the charging station against the
wall, so that the vacuum robot can return
to the charging station independently.
Pay attention to the required clearances
at the charging station.
Note:
Remove any objects within 1 meter from
either side of the station and 2 meters from
the front of the station.
Fig.
3
Press the two rotary brushes labelled
L and R onto the brackets until they
click into place. Pay attention to the
designation
L
and
R
on the device as
well as the brushes..
Remote Control
Fig.
4
Open the battery compartment on the
back of the remote control. Insert two
AAA / LR03 batteries into the battery
compartment. Observe the correct
polarity (+/-) according to the imprint.
Charging the battery
Fig.
5
Switch on the vacuum robot with the
on/ off switch on the bottom (I) . Set it
down in front of the charging station.
Press the on/ standby switch on the
vacuum robot or the charging base
button on the remote control and
then immediately the charging station
button. Make sure the robotic vacuum
cleaner is moving to the charging
station. Before first time use the
built-in batteries must be charged for
at least 12 hours. Subsequent charging
processes will take approx. 4-6 hours
when the battery is empty.
Alternatively, for charging, the DC plug
of the charger can also be connected
directly to the DC socket on the vacuum
robot.
Note:
• Make sure that the charging contacts of
the robot vacuum cleaner and charging
base are not dirty. Clean the contacts if
necessary.
• It is normal for the charging base and
vacuum cleaner to become hot during
charging. This is not a cause for concern.
• Remove the water tank before charging
the robot vacuum cleaner.
Fig.
6
When the battery is charging, the on/
standby switch LED flashes blue. When
the battery is charged, the LED is on
permanently.
LED indicator
LED color Condition
Permanently blue Battery is fully charged
Blue flashing During charging
Indicator light off Product is switched off
Permanently red
Brush roller is blocked
and has to be cleaned
Fig.
7
If the old battery is worn, it can be
replaced by a replacement battery (not
included in the delivery).
Remove the screws and the battery
compartment cover and remove the old
battery. Insert the new battery in the
correct direction to the connector. Close
the battery compartment and tighten
the two screws.
IM_KRVC2320RC_190807_V10_HR.indb 21 7/8/2019 14:43