manualshive.com logo in svg

Kobold DON-05, Operating Instructions Manual

Share
Download
Kobold DON-05 Operating Instructions Manual Download Page 12

DON-H 

page 12 

DON-H 

01/0721

 

b) Wiring diagram with Hall sensor (recommended in connection

with external supply)

7.3.2 

For 1A…5A electronics options 

See supplement to operating instructions ZOK-Ex for electronics options 1A… 5A 

7.3.3 

Calibration Factor (scale or K Factor)   

The  DON  flowmeter  is  delivered  with  a  factory  calibration  certificate.  Within  this 
certificate,  a  calibration  factor  is  provided.  The  calibration  factor  is  a  specific 
representation  of  pulses  per  unit  volume.  (i.e.  pulses  per  liter)  for  that  specific 
meter. 
Measurement devices with attached electronics are factory pre-configured to the 
corresponding calibration factor. Depending on the model, the calibration protocol 
is based on either the flow rate display or the analog output. 
For further details on the operation and parameterization of the electronic option 
Zx and 1A…5A see operating instructions ZOK- (Ex). 

Summary of Contents for DON-05

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands