Knick A405B User Manual Download Page 47

Page: 47 / 108

The alarm delay time delays the color change of the display backlighting to red, the
22 mA signal (if configured), and the alarm contact switching.

Error messages can be signaled by a 22 mA output current. In addition, a relay
contact (RELAY1 / RELAY2) can be configured as alarm contact.

Menu item

Action

Choices

Alarm delay

Enter value using





keys.
Press enter to confirm.

0...600 SEC
(10 SEC)

Sensocheck

Select Sensocheck (continuous
monitoring of sensor membrane
and lines).
Select ON or OFF using



keys.
Press enter to confirm.
(At the same time, Sensoface is
activated. With OFF, Sensoface is
also switched off.)

ON/OFF

Tempcheck

To monitor the temperature
probe with TC OFF selected:
Select Tempcheck ON using



keys.
Press enter to confirm.
Now, the temperature probe will
be monitored.

ON/OFF

Configuring the Alarm

Summary of Contents for A405B













































































































Search results

Summary of Contents for A405B

Reviews:

Related manuals for A405B

Brands by name

Popular brands

Knick A405B, User Manual

Search results

Summary of Contents for A405B

Reviews:

Related manuals for A405B

Brands by name

Popular brands