background image

Diaphragm Pump NMS 030 

 

Use 

KNF Micro BA306116-306115 NMS030-EN 0221 

Operating and Installation Instructions 

2.  Use 

2.1.  Intended use 

KNF pumps in the NMS030 range are to transfer, evacuate and 
compress gases. 

Owner's responsibility 

Only install and operate the pumps under the operating parameters 
and conditions described in Chapter 4, Technical data. Only com-

pletely installed pumps may be taken into service. 
Before using a medium, check whether the medium can be trans-
ferred danger-free in the specific application case. 
Before using a medium, check the compatibility of the materials of 
the pump head, pump housing, diaphragm and valves with the me-

dium. 
The temperature of the medium must lie within the permissible 
temperature range (see Chapter 4). 
The transferred gas should not contain particles as these can pre-
vent the pump from working correctly. If this cannot be guaranteed, 
a filter < 100 

m with sufficiently large filter area must be used up-

stream of the pump. 
See the type- plate or data sheet for full electrical and pneumatic 
data.  
 

2.2.  Improper use 

 

 

DANGER 

 

The pumps must not be operated in an explo-
sive atmosphere. 

 
The pumps are not suitable for transferring dusts and liquids.  
 

Please contact your local KNF partner for special designs that 
are not included in the technical specification (

www.knf.com

). 

 

Operating parameters and 

conditions  

Requirements for  

transferred medium 

Summary of Contents for NMS 030 KPDC

















Reviews: