manualshive.com logo in svg

Knauer BlueShadow Series, Manual

Share
Download
Knauer BlueShadow Series Manual Download Page 26

27

Installation

Fig. 21

Exploded view of an electrical valve

Mounting of the valve on the 
valve drive

Delivery ex works

All valve drives are delivered with a ready-mounted injection or 
multiposition valve. For repeat orders, the electrical valves are 
delivered with included adapter plate.

Screw the adapter plate to the back side of the valve.

1. Attach the adapter plate the right way around. The openings 

for the countersunk screws point to the front.

2. Fasten the adapter plate with two Phillips-head screws (M3). 

Tighten the Phillips-head screw firmly.

Fig. 22

Back side of the electrical valve – adapter plate 
for mounting

Legend

A. Axial plate

B. Axial needle bearing

C. Compensation plate

D. Disk spring

E. Rotor

F. Rotor seal

G. Seal ring

A
B

C
D

F

E

G

Legend

A.  Back side of an elec-

trical valve

B. Markings for the 

mounting

C. Opening for the 

drive axle of the 
valve drive

D. Adapter plate for 

the mounting

E. Opening for coun-

tersunk screws

F. Phillips-head screws

A

B

C

D

E

F

Summary of Contents for BlueShadow Series




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands