Knauer Azura VU 4.1 Instructions Manual Download Page 32

Page: 32 / 47

AZURA® Valve Unifier VU 4.1 Instructions V6855

Operation 23

7.4.1

Start display

After switching on the device, the start display appears. After a short time,

the view changes to the main display.

Menu

Explanation

Figure

Start display

Shows manufacturer and

device name.

VALVE

DRIVE

7.4.2

Main display

The main display is the default view of the device. You can return from

any point of the menu to this display by using one of these options:

Wait for 10 seconds.

Press the confirmation button.

Press the selection button for 3 seconds.

Menu

Explanation

Figure

Main display

Shows the RFID status (icon in

upper right corner), the current

valve posi tion (left number)

and the total num ber of valve

positions (right number).

POS

1 / 4

7.4.3

Main menu

Press the selection button to enter the main menu from the main display.

Scroll through the main menu using the navigation buttons. Confirm with

selection button to enter the submenu.

Menu

Explanation

Figure

Drive Setup

Set the valve drive.

DRIVE

SETUP

Drive GLP

Retrieve GLP data of the valve

drive.

DRIVE

GLP

Valve GLP

Retrieve GLP data of the valve.

ALVE

GLP

Summary of Contents for Azura VU 4.1
















































Search results

Summary of Contents for Azura VU 4.1

Reviews:

Related manuals for Azura VU 4.1

Brands by name

Popular brands

Knauer Azura VU 4.1, Instructions Manual

Search results

Summary of Contents for Azura VU 4.1

Reviews:

Related manuals for Azura VU 4.1

Brands by name

Popular brands