manualshive.com logo in svg

KMC Controls KMD-5551E, Application Manual

Share
Download
KMC Controls KMD-5551E Application Manual Download Page 8

Accessories and replacement parts

The following accessories and replacement parts are available from KMC Controls, Inc.

Power transformer

XEE-6111-50

Transformer, 120-to-24 VAC, 50 VA, single-hub

XEE-6112-50

Transformer, 120-to-24 VAC, 50 VA, dual-hub

Surge suppressors

KMD-5567

EIA-485 surge suppressor for MS/TP or Tier 2 networks

Cables

HPO-5551

Conquest Router Tech Cable Kit–Includes USB, Ethernet, and
MS/TP to NetSensor cables

HSO-9001

Ethernet cable, 50 feet

HSO-9011

Ethernet cable, 50 feet, plenum rated

Replacement parts

HPO-9901

Controller replacement parts kit with terminal blocks and DIN clip

License

DR-KMD-TRANS

Niagara license for any KMD-5551E translator discovered by a
station

Mounting the translator

For permanent installations, the translator can be flush mounted or snapped to a 35 x 75 mm
DIN rail. For translator dimensions, see the topic

Specifications

on page 5

.

Surface mounting

Extend the mounting tabs away from the translator body and fasten with

screws.

Illustration 1–1 Surface mounting the translator

Extend mounting tabs

6.00 in.

152 mm

DIN rail mounting

Mount the DIN rail and then do the following:

1

Extend the mounting tabs.

2

Place the bottom of the router over the DIN rail.

3

Push the mounting tabs back toward the router body to lock it to the rail.

Section 1: Introduction

KMC Controls, Inc.

8

Revision B

Summary of Contents for KMD-5551E



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands