manualshive.com logo in svg

KMC Controls KMD-5551E, Application Manual

Share
Download
KMC Controls KMD-5551E Application Manual Download Page 5

Sec ti o n 1:

In tr o d u c ti o n

This section provides a description of the KMC Controls KMD-5551E translator. It also
introduces safety information. Review this material before installing or operating the
translator.

The KMC Controls KMD-5551E translator is a BACnet to KMDigital translator. The translator
highlights are:

l

Translates between one KMD Tier 1 controller and one KMD Tier 2 network to a
BACnet virtual network.

l

Compatible with Niagara

AX

and Niagara 4 Frameworks.

l

Easy to install and simple to configure.

l

Configured from internally served web pages.

l

Internal network diagnostics and route status reports.

Topics in this section

Specifications

5

Accessories and replacement parts

8

Mounting the translator

8

Connecting for network routing

9

Connecting power

10

Single-cable connection

12

Maintenance

13

If you encounter difficulty

13

Specifications

Specifications are subject to change without notice.

Communication ports

BACnet Ethernet, BACnet IP, KMD Tier 1

10BaseT/100BaseT, RJ–45 connector

KMD Tier 2

One optically isolated Tier 2 port, 9.6–38.4 kilobaud

Removable three-screw terminal block, 12–22 AWG wire

Switched end-of-line termination

USB

USB micro B connection for temporary power

KMD-5551E Translator

Revision B

5

Summary of Contents for KMD-5551E



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands