background image

SAFETY PRECA

UTIONS

WARNING TO AVOID SERIOUS INJURY:

‡

  Adult assembly is required.

‡

  Continuous adult supervision is required.

‡

  This product should only be used by persons 8+ years of age.

‡

  Never ride with more than one person. Maximum weight is 180 lbs (82Kg).

‡

  Excessive weight may cause a hazardous or unstable condition.

‡

  Always wear an approved helmet while riding, with the chinstrap securely fastened.

‡

  Always wear shoes when riding.

‡

  Always wear kneepads, wrist guards, gloves, and elbow pads when riding.

‡

  Do not ride the product at dusk, at night or at times of limited visibility.

 

 

‡

 

Always comply with local laws and regulations.

‡

 

Ride on smooth paved surfaces. Do not ride on streets or roadways.

‡

  Do not ride off road, on grass or wet surfaces.

‡

 

Never use near motor vehicles.

‡

 

Do not ride the product over curbs or bumps that can damage the steering mechanism.

‡

 

Do not ride on hills, steeply sloped areas, on or near steps, near swimming pools, or in alleys. 

‡

  Not intended for jumping.

‡

  The brake may be hot after continuous use. Do not touch after braking.

‡

  Check brakes and secure all fasteners before every ride.

‡

  Do not wear headphones or anything else that would impair your ability to hear or see. 

‡

  Understand all operating procedures before riding.

Summary of Contents for 43033430

























Reviews: