KitchenAid KUDD03DT Technical Education Download Page 2

Page: 2 / 70

- ii -

WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on

our products by anyone other than authorized In-Home Service Professionals.

FORWARD

This KitchenAid Job Aid Double Drawer Dishwasher (Part No. 4317427), provides the In-Home

Service Professional with information on the installation, operation, and service of the Double

Drawer Dishwasher. For specific information on the model being serviced, refer to the “Use and

Care Guide,” or “Tech Sheet” provided with the oven.
The Wiring Diagram and Strip Circuits used in this Job Aid are typical and should be used for

training purposes only. Always use the Wiring Diagram supplied with the product when servicing

the oven.

GOALS AND OBJECTIVES

The goal of this Job Aid is to provide information that will enable the In-Home Service Professional

to properly diagnose malfunctions and repair the Double Drawer Dishwasher.

The objectives of this Job Aid are to:

•   Understand and follow proper safety precautions.
•   Successfully troubleshoot and diagnose malfunctions.
•  Successfully perform necessary repairs.
•  Successfully return the oven to its proper operational status.

2008, Whirlpool Corporation, Benton Harbor, MI 49022

Summary of Contents for KUDD03DT







































































Search results

Summary of Contents for KUDD03DT

Reviews:

Brands by name

Popular brands

KitchenAid KUDD03DT, Technical Education

Search results

Summary of Contents for KUDD03DT

Reviews:

Brands by name

Popular brands