34
3.
Replace with alkaline 1.5-volt “D” size battery.
4.
If your model has two battery compartments, repeat steps 2
and 3 for the other battery compartment.
5.
Close inner compartments. Cover will snap into place.
6.
Close outer cover.
IMPORTANT:
In the event of a power outage, for models with an
electronic display, the batteries must be installed in order for the
electronic display and the integrated gas flow valve to function.
The batteries must be installed in order to light the grill manually.
General Cleaning
IMPORTANT:
Before cleaning, make sure all controls are off and
the grill is cool. Always follow label instructions on cleaning
products.
For routine cleaning, wash with soap and water using a soft cloth
or sponge. Rinse with clean water and dry at once with a soft,
lint-free cloth to avoid spots and streaks.
Do not use steel wool to clean the grill, as it will scratch the
surface.
To avoid damage to the finish from weather, use vinyl grill cover,
available from your local dealer. See “Assistance or Service”
section.
STAINLESS STEEL
IMPORTANT:
To avoid damage to stainless steel surfaces, do not
use soap-filled scouring pads, abrasive cleaners, Cooktop
Polishing Creme, steel wool, gritty wash cloths or paper towels.
Cleaners should not contain chlorine. Damage may occur.
Food spills should be cleaned as soon as entire grill is cool. Spills
may cause permanent discoloration.
Cleaning Method:
■
Rub in direction of grain to avoid scratching or damaging the
surface.
■
Stainless Steel Cleaner and Polish Part Number
31462 (not included):
See “Assistance or Service” section to order.
■
Liquid detergent or all-purpose cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
■
Vinegar to remove hard water spots.
■
Glass cleaner to remove fingerprints.
GRILL GRATES
IMPORTANT:
To avoid damage to grill grates, do not use a steel
or fiber scraper. Immediately after you are finished cooking,
loosen food soil with a brass bristle brush. Turn all burners to HI
for 10-15 minutes with the hood closed to burn off food soil. Turn
off all burners, raise the hood and let grates cool. Use the brass
bristle brush to remove ash from the grill grates.
When completely cool, grill racks can be removed for thorough
cleaning. Clean them with a mild detergent and warm water.
For baked-on soil, prepare a solution of 1 cup (250 mL) ammonia
to 1 gal. (3.75 L) water. Soak grates for 20 minutes, then rinse
with water and dry completely.
WARMING SHELF
Cleaning Method:
■
Liquid detergent or an all-purpose cleaner.
■
Rinse with clean water and dry with soft, lint-free cloth.
■
For tough spots or baked-on grease, use Heavy Duty
Degreaser Part Number 31552, a commercial degreaser
designed for stainless steel.
See “Assistance or Service” section to order.
IMPORTANT:
Make sure gas supply is off and all control knobs
are in the OFF position. Make sure the side burner is cool.
EXTERIOR
The quality of this material resists most stains and pitting,
providing that the surface is kept clean, polished and covered.
■
Apply stainless steel polish to all non-cooking areas before
first use. Reapply after each cleaning to avoid permanent
damage to surface.
■
Cleaning should always be followed by rinsing with clean
warm water.
■
Wipe the surface completely dry with a soft cloth.
■
For tough spots or baked-on grease, use Heavy Duty
Degreaser Part Number 31552, a commercial degreaser
designed for stainless steel.
See “Assistance or Service” section to order.
INTERIOR
Discoloration of stainless steel on these parts is to be expected,
due to intense heat from the burners. Always rub in the direction
of the grain. Cleaning should always be followed by rinsing with
clean, warm water.
Cleaning Method:
■
Liquid detergent or all-purpose cleaner.
■
Rinse with clean water and dry completely with a soft, lint-
free cloth.
■
A heavy-duty scrub sponge can be used with mild cleaning
products.
■
For small, difficult-to-clean areas, use Heavy Duty Degreaser
Part Number 31552, a commercial degreaser designed for
stainless steel.
See “Assistance or Service” section to order.
U-SHAPED BURNERS
Cleaning Method:
■
Clear any clogged burner ports with a straightened paper
clip. Do not use a toothpick because it may break off and
clog the port.
■
Check and clean burner/venturi tubes.
1.
Remove grill grates and sear plates.
2.
Remove the 2 screws that hold the burner in place.
Remove gas burner from the grill.
3.
Use a flashlight to inspect into the gas burner through the
burner inlet to ensure there is no blockage. If any
obstruction is seen, use a metal coat hanger that has
been straightened to clear them.
4.
After inspecting the inside of gas burner for blockage,
reassemble burner by sliding the middle tube of the gas
burner over the gas orifice.
A. 2 screws
A
Summary of Contents for KBNS271TSS
Page 39: ...39 Notes ...
