background image

GENERAL GLASS INFORMATION

8

The venting system (chimney) of this appliance should be inspected at least once a year and if needed, your venting
system should be cleaned.

Keep the area around your appliance clear of combustible materials, gasoline and other flammable vapours and
liquids.

Under no circumstances should this appliance be modified. Parts that have to be removed for servicing should be
replaced prior to operating this appliance again.

Installation and any repairs to this appliance should be done by a qualified service person. A professional service
person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances
checked annually.

Never use your gas stove as a cooking device.

The Burner/Log Assembly has been engineered and permanently adjusted for proper flame control.

Periodically remove the logs from the grate assembly and vacuum any loose particles from the grate and burner areas.

This appliance should not be used as drying rack for clothing, nor should Christmas stockings or decorations be hung
near it.

Under no circumstances should any solid fuels (wood, paper, cardboard, coal) be used in this appliance.

NOTE: it is normal for your gas stove to give off some odour the first time it is burned. This is due to the curing
of the paint and any undetected oil from the manufacturing process.

Please ensure that your room is well ventilated - open all windows.

It is recommended that you burn your gas stove for at least four (4) hours the first time you use it without the fan on.

GLASS CLEANING

It will be necessary to clean the glass periodically. During start-up, condensation, which is normal, forms on the inside
of the glass and causes dust, lint etc. to cling to the glass surface. Also, initial paint curing can deposit a slight film
on the glass. It is therefore recommended that initially the glass be cleaned two or three times with non-abrasive
common household cleansers and warm water. After that, the glass should be cleaned two or three times a season
depending on the circumstances.

DO NOT ALTER GAS ORIFICE.

f i r e - p a r t s . c o m

Summary of Contents for FV5000



















Reviews: