background image

17

For models wIth 

non-AdjustAble 

regulAtors wIth 

mAnuAl VAlVes

1.  Check  that  the  casting  is  properly 

located  as  per  the  diagram  and 

that the orifice is properly located in 

respect to the jet pipe. (Figure 1)

2.  Make certain that the manual valves 

are  turned  to  the  OFF  position  by 

turning  them  clockwise  until  they 

reach the stop position. 

3.  Open  the  cylinder  control  valve  by 

turning  it  counterclockwise  as  per 

the diagram (Figure 2).

4.  To light the jet burner, hold a multi-

purpose lighter or paperback match 

over  the  jet  pipe  as  per  (Figure 

3). Turn the corresponding manual 

valve control toward the ON position 

until  ignition  occurs.  Turning  the 

manual  valve  counterclockwise 

increases the gas flow to the burner 

and  hence  the  flame  size  (Figure 

2).  To  light  the  cast  burner,  hold 

a  multipurpose  lighter  or  use  a 

paperbook match placed above the 

casting  as  per 

(Figure  4)

.  Turn 

the  corresponding    manual  valve 

control toward the ON position until 

ignition occurs. Turning the manual valve counterclockwise increases the gas flow to the burner 

and  hence  the  flame  size  (Figure  2).  When  lighting  the  stove,  if  ignition  does  not  occur  in  3  to 

5 seconds, turn the manual valve(s) and cylinder control off. Wait 5 minutes for gas to disperse. 

Repeat Procedure.

5.  Refer to 

(Figure 5) for proper flame emission for the jet and cast burners. The casting flame should 

be blue and the flame should be emitted from every port in the casting. If not, rotate the air shutter 

position until there is a blue flame. Opening the shutter too much will cause the flame to “lift” off 

the burner. If there is a yellow flame, or if some ports have no flame, this indicates there may be an 

obstruction in the venturi tube or ports. Check the maintenance instructions on page 18 for more 

information regarding a yellow flame.

6.  Always monitor the flame throughout the cooking process. If at any point in the cooking process 

the flame(s) are accidently extinguished, immediately turn the manual valve(s) and cylinder valve 

OFF.  Wait 5 minutes for gas to disperse and relight the cooker according to the lighting insructions 

(#1 - #5) in this section.

neVer put hAnds or FAce dIrectly oVer burner whIle lIghtIng

or whIle the ApplIAnce Is lIt.

Summary of Contents for OUTDOOR COOKERS

























Reviews: