Kilews KFA-0820H Instruction Manual Download Page 3

Page: 3 / 26

CONTENTS

CHECK BEFORE OPERATION ........................................................

CHECK THE SCREW SIZE ...............................................................................

FUNCTIONS WITH ADJUSTING HOLES ON HOUSING AND PCB ...

ADJUSTMENT ..............................................................................

ADJUST THE RAIL ASSEMBLY ........................................................................

DISMANTLE THE RAIL ASSEMBLY ............................................................

ADJUST THE WIDTH OF RAIL ASSMEBLY .................................................

INSERT THE RAIL ASSEMBLY ..................................................................

ADJUST THE HOLDING PLATE ........................................................................

ADJUST THE FEEDING STRUCTURE ............................................................

ADJSUT THE SENSOR FUNCTION .................................................................

ADJUST THE GUIDE ....................................................................................

ADJUST THE BRUSH ...................................................................................

OPERATION METHOD ................................................................

LOAD SCREWS INTO CHAMBER ...................................................................

PICKING UP SCREW ....................................................................................

DISPLAY PANEL OPERATION........................................................................

MAINTENANCE & TROUBLE SHOOTING .....................................

MAINTENANCE & CLEANING .....................................................

INTERNATIONAL WARRANTY CONDITIONS ..............................

Summary of Contents for KFA-0820H


























Search results

Summary of Contents for KFA-0820H

Reviews:

Related manuals for KFA-0820H

Brands by name

Popular brands

Kilews KFA-0820H, Instruction Manual

Search results

Summary of Contents for KFA-0820H

Reviews:

Related manuals for KFA-0820H

Brands by name

Popular brands