background image

 

22

 

WARRANTY CARD 

The  warranty  is  valid  for  12  months  from  purchase  date  (based  on  8 

working  hours  a  day).  Please  contact  your  supplier  during  the  warranty 

period for repair or maintenance. 

 

NOTE:   

1. The service cost shall be considered as chargeable if the failure/cost was 

induced by any of the following conditions: 

-Failure due to improper handling or un-authorized modification. 

-Failure has nothing to do with the original design of the machine. 

-Labor and parts cost to replace the consumable parts (brush, motor, rail assembly, 

etc.). 

2. The WARRANTY will be void under any of the following conditions: 

-Failure arising from a case or an accident beyond one’s control or Act of God. 

-It has been modified, altered and/ or repaired by an unauthorized dealer, purchaser or 

third party. 

-The serial number, warranty card has been altered, de-faced and /or removed. 

-Failing to use genuine parts sold or recommended by the Company. 

3. Under this warranty, the company only provides service at any time 

during normal business hours. Should emergency service is required outside 

normal business hours, and such service if available will be provided with a 

charge on a per call rate basis. 

4. The warranty is not transferable without the consent of the Company

Summary of Contents for KFA-0820H



























Reviews: