Kilews KFA-0820A Page 3 Instruction Manual Download

Page: 3 / 23

CONTENTS

CHECK BEFORE OPERATION .......................................................

１

CHECK THE SCREW SIZE ..............................................................................

１

FUNCTIONS WITH ADJUSTING HOLES ON HOUSING AND PCB ..

１

ADJUSTMENT .............................................................................. 2

ADJUST THE RAIL ASSEMBLY ......................................................................... 2

DISMANTLE THE RAIL ASSEMBLY ............................................................. 2

ADJUST THE WIDTH OF RAIL ASSMEBLY .................................................. 5

INSERT THE RAIL ASSEMBLY ................................................................... 7

ADJUST THE HOLDING PLATE ......................................................................... 9

ADJUST THE FEEDING STRUCTURE ............................................................. 10

ADJSUT THE SENSOR FUNCTION .................................................................. 11

ADJUST THE BRUSH .................................................................................... 12

OPERATION METHOD ................................................................ 13

LOAD SCREWS INTO CHAMBER .................................................................... 13

DISPLAY PANEL OPERATION......................................................................... 14

MAINTENANCE & TROUBLE SHOOTING ..................................... 17

MAINTENANCE & CLEANING ..................................................... 18

INTERNATIONAL WARRANTY CONDITIONS .............................. 19

Summary of Contents for KFA-0820A























Search results

Summary of Contents for KFA-0820A

Reviews:

Related manuals for KFA-0820A

Brands by name

Popular brands

Kilews KFA-0820A, Instruction Manual

Search results

Summary of Contents for KFA-0820A

Reviews:

Related manuals for KFA-0820A

Brands by name

Popular brands