KIKKA BOO PRIMA 3in1, Instructions For Use Manual

Page: 10 / 30

WARNINGS
• Read the instructions carefully before use and keep them for future reference. The child may be hurt if you do not follow these instructions.
• Do not leave the child unattended!
• Always use the restraint system!
• Prevent your child from climbing on the product.
• Do not use the high chair unless all components are correctly fitted and adjusted!
• Do not use the chair near open fair and heating devices!
• Be aware of the risk of tilting when your child can push its feet against a table or any other structure.
• Do not move or lift the product while the child is inside.
• Do not use the product until the child can sit up unaided.
• Keep children away when assembling and disassembling the product to avoid injury.
• Always check the security and the stability of poduct before use.
• Always use the chair with a harness system! Make sure that any harness is correctly fitted.
• Keep the chair away from children when do not use it!
• The chair must not be used as a toy!
• Do not allow your child to stand up whilst in the high chair!
• Please ensure that the high chair is assembled by an adult!
• Highchair is intended for children from 6 months to 3 years or a maximum weight of 15kg.
• Position the highchair on a flat,even and horizontal floor and do not elevate the highchair on any structure or table.
• Do not use the product if any part is broken, torn or missing.
• Product located under a window could be used as a step by the child and cause the child to fall out of the window.
• Complies with EN16120
I. PARTS LIST
1. Seat cover; 2. Seat unit; 3. Legs for chair; 4. Legs for table; 5. Half of table plate; 6. Tray; 7. Five point harness system;
PACKAGE
1. Seat cover (1pcs); 2. Seat unit (1pcs); 3. Front legs for chair (2pcs) rear legs for chair (2pcs); 4. Front and rear legs for table (4pcs); 5. Half of table plate (2pcs); 6. Tray with
cover plate (1pcs); 7. Five point harness system (1pcs); 8. Bolts(4pcs);
Please confirm the package and accessories and make sure there is no missing.
II. CHILD CHAIR AND TABLE VERSION
III. ASSEMBLY
3.1. lnsert the front two legs into two front holes at the botton of the seat unit until the pin click into place.
Insert the rear two legs in the same way. A- Rear legs; B-Front legs; C-pin;
3.2. Connect the two half of table plates together as shown in picture,then fix them with four bolts into four holes.
D- Hole with nut in it;
3.3.To assemble the four table legs, inser t the leg into the hole at the bottom of table plate. Please note that there is a nut in the hole, then screw the leg until it is fixed.
3.4. If the foot of the table is in the wrong position after the table legs are installed, please follow the arrow to rotate.
3.5.Put the seat cover on the seat unit. There are four slots in the backrest and slots at the bottom, to fix the safety belts, pass the end buckle of shoulder belts through the
two upper slots. Pass the end buckle of waist belts through the two lower slots, pass the end buckle of crotch belt through the botton one. Е-slot;
3.6. Position the tray over the armrests, holding the latch mechanism at both sides of the tray, at the same time sliding the tray onto the chair with the desired position.
Then release the latch and move the tray until a click . 1. Lock; 2. Hold the latch, unlock;
3.7. The tray can be set in four positions, using the latches at both sides to adjust the position.
3.8. In order to wash the tray, you may remove its cover plate by releasing its two catches and three block. A- Block; B-Catch;
3.9. Connect the chair and table together to be a high chair: Plug the four legs of chair into the four holes on the table until the pin click into place.
3.10. Feeding Highchair version can be separated into Child chair and table function. Тhere are four buttons under the table plate. Press the button and leg will be released
from the table. C-button;
3.11. To buckle the safety belts, connect th shoulder and waist belts and then snap them into the crotch belts claps. To unbuckle the safety belts, press the button in the
middle of the clasp. Sliding adjusters are fitted and should be carrefully adjusted so the harness fits your child comfortably. The safety belts can be removed for cleaning
purposes by sliding the end buckle of belts through the five slots.
MAINTENANCE AND CLEANING
The product requires regular maintenance to keep it in good working order.Regular check all parts of rhe product to ensure that they are operating correctly and for signs of
wear or damage.
Moving parts may be lubricated with a light silicone oil. Do not use this product if any part is broken,torn or missing and use only spares provided by the manufacturer.Only
replacement parts supplied or recommented by the manufacturer should be used.
1. Chair and table: Wash wish clean and damp cloth and mild soap.
2. Seat cover and belts:Wash in hands. Do not bleach. Do not tumble-dry. Do not dry clean.
ENGLISH