background image

9404035E

X

INSTALLATION AND OPERATING INSTRUCTIONS

MEADOWVALE II PLAY SYSTEM - F24035EX

To reduce the risk of serious injury or death, you must read and 

follow these instructions. Keep and refer to these instructions often 

and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 24’10” x 28’ (7.9 x 8.5 m) area requires Protective Surfacing. See page 3. 
MAXIMUM VERTICAL FALL HEIGHT -  6’11” (2.1 m) 
CAPACITY - 6 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.

Warning. Only for domestic use.

4 - 8 Hrs

Two person

assembly

WARNING 

28’ / 8.5m

12’10” / 3.9m

24’10” / 7.9m

10’6” / 3.2m

Rev 06/18/2020

Table of Contents

Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood – Limited Warranty  . . . . . . . . . . . . . . pg. 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 6
Metric Conversion Sheets  . . . . . . . . . . . . . . . . . . . . . pg. 7,8
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 9
Installation of I.D./Warning Plaque  . . . . . . . . . . . .Final Step

KidKraft, Inc.

4630 Olin Road

Dallas, Texas 75244 USA

[email protected]

[email protected]

1.800.933.0771

972.385.0100

For online parts replacement visit

https://parts.kidkraft.com/

KidKraft Netherlands BV

Olympisch Stadion 8

1076 DE Amsterdam

The Netherlands

[email protected]

+31 20 305 8620 M-F from 09:00 to 17:30

(GMT+1)

For online parts replacement visit

https://parts.kidkraft.eu/

Summary of Contents for F24035EX









































Reviews: