KidKraft CRANBROOK PLAY SYSTEM Installation And Operating Instructions Manual Download

Page: 69 / 76

Step 33: Connect Monkey Bar Assembly to Fort

Part 1

Attach 2 MB Hanger Brackets to (2553) MK Board with 2 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer, flat

washer and t-nut) per bracket as shown in fig. 33.1 and 33.2.

Place each (1565) MK Rail Short of the Monkey Bar Assembly from Step 10 in each MB Hanger Bracket and

attach with 1 (PB5) 1/4 x 2” Pan Bolt (with flat washer x 2 and lock nut) per bracket. (fig. 33.3)

From inside the assembly attach (2553) MK Board to each (1565) MK Rail Short with 2 (S4) #8 x 3” Wood

Screws per rail. (fig. 33.3)

Fig. 33.1

2553

1/4” Lock

Washer

1/4”

T- Nut

Fig. 33.3

Hardware

4 x

1/4 x 1-1/4” Pan Bolt

(1/4” lock washer, 1/4” flat washer & 1/4” t-nut)

2 x

1/4 x 2” Pan Bolt

(1/4” flat washer x 2 & 1/4” lock nut)

4 x

#8 x 3” Wood Screw

2 x MB Hanger Bracket

Other Parts

MB Hanger

Bracket

1/4” Flat

Washer

PB2

PB5

Fig. 33.2

PB2

PB5

1/4” Flat

Washer

1/4”

Lock Nut

1565

2553

Summary of Contents for CRANBROOK PLAY SYSTEM













































































Search results

Summary of Contents for CRANBROOK PLAY SYSTEM

Reviews:

Related manuals for CRANBROOK PLAY SYSTEM

Brands by name

Popular brands

KidKraft CRANBROOK PLAY SYSTEM, Installation And Operating Instructions Manual

Search results

Summary of Contents for CRANBROOK PLAY SYSTEM

Reviews:

Related manuals for CRANBROOK PLAY SYSTEM

Brands by name

Popular brands