KidKraft CRANBROOK PLAY SYSTEM Installation And Operating Instructions Manual Download

Page: 62 / 76

Step 29: Lower Front Wall Assembly

Part 2

Hardware

Wood Parts

24 x

#8 x 7/8” Truss Screw

Front Wall

2383

Fig. 29.4

Fig. 29.3

5265

2350

2554

2556

(hidden)

Flush

Tight to the top of (2554) Front Ground and flush to the outside edge of (2383) Post evenly space and

attach 6 (2556) CE Siding to (2383) Post and (2377) Lower Post with 2 (S0) #8 x 7/8” Truss Screws per board,

as shown in fig. 29.3 and 29.4. Make sure there are no gaps between boards.

Tight to the bottom of (2350) Front Floor and flush to the outside edge of (2383) Post attach 6 (2556) CE

Siding to (2383) Post and (2377) Lower Post with 2 (S0) #8 x 7/8” Truss Screws per board, as shown in fig.

29.3 and 29.4. Make sure there are no gaps between boards.

x 2 per

board

12 x

CE Siding 3/8 x 3-1/2 x 28”

2556

2377

Summary of Contents for CRANBROOK PLAY SYSTEM













































































Search results

Summary of Contents for CRANBROOK PLAY SYSTEM

Reviews:

Related manuals for CRANBROOK PLAY SYSTEM

Brands by name

Popular brands

KidKraft CRANBROOK PLAY SYSTEM, Installation And Operating Instructions Manual

Search results

Summary of Contents for CRANBROOK PLAY SYSTEM

Reviews:

Related manuals for CRANBROOK PLAY SYSTEM

Brands by name

Popular brands