KidKraft CRANBROOK PLAY SYSTEM Installation And Operating Instructions Manual Download Page 51

Page: 51 / 76

Step 25: Lower Swing Wall Assembly

Part 2

From inside the assembly measure 1-1/4” down from the top of (2422) Lower Back then place 2 (1858)

Short Wall Supports over the pilot holes of the (2413) CE Siding then attach to (2422) Lower Back and (2558)

Ground Back with 4 (S1) #8 x 1-1/8” Wood Screws per board. (fig. 25.3 and 25.4)

From outside of the assembly attach (1858) Short Wall Supports to each (2413) CE Siding with 2 (S0) #8 x

7/8” Truss Screws per siding. (fig. 25.5)

Hardware

Wood Parts

8 x

#8 x 1-1/8” Wood Screw

12 x

#8 x 7/8” Truss Screw

2 x

Short Wall Support 1 x 4 x 24-1/4”

1858

Fig. 25.3

Inside View

2413

x 2 per board

2558

2422

1858

(hidden)

Fig. 25.4

Fig. 25.5

1858

x 4 per

board

1-1/4”

2413

Outside View

Summary of Contents for CRANBROOK PLAY SYSTEM













































































Search results

Summary of Contents for CRANBROOK PLAY SYSTEM

Reviews:

Brands by name

Popular brands

KidKraft CRANBROOK PLAY SYSTEM, Installation And Operating Instructions Manual

Search results

Summary of Contents for CRANBROOK PLAY SYSTEM

Reviews:

Brands by name

Popular brands