KidKraft Cedar Summit Canyon Ridge Installation And Operating Instructions Manual Download

Page: 74 / 114

Step 29: Attach Elbow Assemblies and TNR2 Slide

Support

Hardware

1 x

#12 x 1” Pan Screw

1 x

1/4 x 1” Pan Bolt

(1/4” flat washer & 1/4” lock nut - previously removed)

16 x

1/4 x 3/4” Pan Bolt

(1/4” lock nut)

PB6

Other Parts

1 x TNR3 Tube Support

4 x TNR2 Slide Clamp Ring

PB1

Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round

recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until

further step.

Attach the two remaining Elbow Assemblies as instructed in Steps 26 and 27.

Place TNR Brace Assembly against (041) Narrow Back Panel so it sits under the slide. It is not attached yet.

(fig. 29.1)

On the fourth attached Elbow Assembly remove the pan bolt and nut which is facing the fort (installed in Step

24). (fig. 29.1)

The bolt will no longer be needed, but keep the lock nut.

Loosely attach TNR3 Tube Support (at the slightly bent end) to the Clamp Ring using 1 (PB6) 1/4 x 1” Pan

Bolt (with flat washer and the previously removed lock nut). (fig. 29.2)

Rotate TNR3 Tube Support and attach to (040) Slide End Panel using 1 (S6) #12 x 1” Pan Screw as shown

in fig. 29.2.

Fully tighten screw and bolt.

Remove PB1 (1/4 x 3/4”

Pan Bolt) first then install

PB6 (1/4 x 1” Pan Bolt

with flat washer)

Lock

Nut

Fig. 29.1

Fig. 29.2

Attach 2

remaining

Elbow

Assemblies

Flat

Washer

Note: Flat

end down

TNR 3 Tube

Support

040

TNR Brace

Assembly

041

PB6

Summary of Contents for Cedar Summit Canyon Ridge



















































































































Search results

Summary of Contents for Cedar Summit Canyon Ridge

Reviews:

Related manuals for Cedar Summit Canyon Ridge

Brands by name

Popular brands

KidKraft Cedar Summit Canyon Ridge, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit Canyon Ridge

Reviews:

Related manuals for Cedar Summit Canyon Ridge

Brands by name

Popular brands