KidKraft BEAR CAVE LODGE Installation And Operating Instructions Manual Download Page 80

Page: 80 / 153

Step 36: Attach Transom Boards

Tight to (2802) Transom Window and flush to the bottom of (2788) Mid Roof Support attach 1 (2790) Transom

Board A to (2788) Mid Roof Support and (2793) Long Roof End with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 36.1

and 36.2)

Tight to (2790) Transom Board A and flush to the bottom of (2788) Mid Roof Support attach 1 (2791) Transom

Board B to (2788) Mid Roof Support and (2793) Long Roof End with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 36.1

and 36.2)

Repeat Steps A and B for all 4 corners.

Fig. 36.1

Fig. 36.2

4 x

Transom Board A 1 x 5 x 15-1/2”

4 x

Transom Board B 1 x 6 x 11”

Wood Parts

Hardware

2790

32 x

#8 x 1-1/2” Wood Screw

2791

x 4 per board

2788

2802

2793

Tight

Flush

2802

2793

2788

2790

2791

2790

2791

2790

2791

2790

2791

Summary of Contents for BEAR CAVE LODGE


























































































































































Search results

Summary of Contents for BEAR CAVE LODGE

Reviews:

KidKraft BEAR CAVE LODGE, Installation And Operating Instructions Manual, Page: 80 / 153

Search results

Summary of Contents for BEAR CAVE LODGE

Reviews: