manualshive.com logo in svg

KidKraft BEAR CAVE LODGE, Installation And Operating Instructions Manual, Page: 102 / 153

Share
Download
KidKraft BEAR CAVE LODGE Installation And Operating Instructions Manual Download Page 102

 102 

A:

  Place 1 Hand Grip over the existing holes in (0602) Short Side Trim, making sure that it’s centered and flush 

to the edges. Pre-drill with a 1/8: (3.2mm) drill bit and attach Hand Grip with 2 (LS2) 1/4 x 2-1/2” Lag Screws 

(with flat washers). (fig. 51.1 and 51.2)

B:

 Repeat step to install a second Hand Grip on the other side.

Step 51:  Attach Hand Grips

centred on face and

flush to edge of Side Trim,

both sides

1/4” flat 

washer

1/4” flat 

washer

Steel Hand Grip

per side

Fig. 51.1

Short Trim

15.9 x 76.2 x 402mm

LS2

1/4 x 2-1/2" Lag Screw

w/ flat washer

X4

centred on face and 

flush to edge of Side Trim, 

both sides

Side Trim

15.9 x 76.2 x 515mm

0601

LS2

LS2

Hardware

4 x 

 ¼ x 2-1/2” Lag Screws (with flat washers)

2 x Steel Hand Grip

Other Parts

LS2

Fig. 51.2

Summary of Contents for BEAR CAVE LODGE


























































































































































Reviews:

No comments