Keysight N5221BU-677 Page 38 Installation Note Download | Manualshive

Page: 38 / 54

background image

38 Installation Note N5222-90129

Installation Procedure for the Upgrade

-

Semirigid Cables Required for Upgrading to an Option 417 PNA’

To see images showing the location of these cables, click the Chapter 6
bookmark “Bottom RF Cables, 4-Port, Option 417, S/N Prefix

≥

6021” in the

PDF Service Guide

. New parts are listed in

Table 2 on page 11

— W26 (N5222-20034) A32 port 2 coupler to front-panel Port 2 CPLR ARM
— W24 (N5222-20053) Port 2 CPLR THRU to A32 port 2 coupler
— W20 (N5222-20054) Port 4 CPLR THRU to A31 port 4 coupler
— W91 (N5222-20022) Port 4 RCVR D IN to A44 port 4 receiver attenuator
— W22 (N5222-20018) A31 port 4 coupler to front-panel Port 4 CPLR ARM
— W80 (N5222-20020) A36 port 4 source attenuator to front-panel Port 4

SOURCE OUT

— W50 (N5222-20027) REF 4 RCVR R4 IN to A24 mixer brick (R4)
— W92 (N5222-20026) A44 port 4 receiver attenuator to A24 mixer brick (D)
— W79 (N5222-20001) A27 port 4 receiver coupler to A36 port 4 source

attenuator

— W21 (N5222-20025) A27 port 4 receiver coupler to front-panel REF 4

SOURCE OUT

— W76 (N5222-20019) A35 port 3 source attenuator to front-panel Port 3

SOURCE OUT

— W89 (N5222-20021) Port 3 RCVR C IN to A43 port 3 receiver attenuator
— W18 (N5222-20015) A30 port 3 coupler to front-panel Port 3 CPLR ARM
— W12 (N5222-20045) Port 1 CPLR THRU to A29 port 1 coupler
— W16 (N5222-20049) Port 3 CPLR THRU to A30 port 3 coupler
— W14 (N5222-20030) A29 port 1 coupler to front-panel Port 1 CPLR ARM
— W36 (reuse) (N5222-20032)REF 1 RCVR R1 IN to A33 reference mixer

switch
* Refer to the note shown in

for information on installing W36

(part number N5222-20032).

Use a 5/16” wrench to hold cable connectors when tightening a mating

semi-rigid cable.

«
...
36
37
38
39
40
...
»

Summary of Contents for N5221BU-677























































Reviews:

No comments

Related manuals for N5221BU-677

Brand: Sequential Pages: 17

Brand: Sequential Pages: 54

Brand: Farfisa Pages: 23

Music Thing Modular SimpleEQ

Brand: Thonk Pages: 27

Brand: Schubert Pages: 68

Brand: Pittsburgh Modular Pages: 6

Brand: Pittsburgh Modular Pages: 7

Voltage Research Laboratory

Brand: Pittsburgh Modular Pages: 14

Lifeforms Percussion Sequencer

Brand: Pittsburgh Modular Pages: 23

Brand: Pittsburgh Modular Pages: 37

Brand: Pittsburgh Modular Pages: 45

Brand: Pittsburgh Modular Pages: 44

Brand: Pittsburgh Modular Pages: 70

Brand: Ploytec Pages: 13

Brand: Mode Machines Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands