Keysight N5221BU-677 Page 46 Installation Note Download

Page: 46 / 54

46 Installation Note N5222-90129

Installation Procedure for the Upgrade

Step 31. Reinstall the Outer Cover

For instructions, click the Chapter 7 bookmark “Removing the Covers” in the
PDF Service Guide

Step 32. Remove Option 217 License

Procedure Requirements

— The analyzer must be powered up and operating to perform this procedure.
— The Network Analyzer program must be running.

— A keyboard and mouse must be connected to the network analyzer.

Option 217 License Removal Procedure

To start the Keysight License Manager, press Start > Keysight License

Manager > Keysight License Manager . A Keysight License Manager dialog

box will appear.

Right click the on the desired option and click

Delete

In the Select Desired Option list, click

217

In the Keysight License Manager dialog box that appears, press or click

Yes

to confirm delete.

A message displays stating that the option removal was successful.

1. See

“Downloading the Online PNA Service Guide” on page 7

Summary of Contents for N5221BU-677























































Search results

Summary of Contents for N5221BU-677

Reviews:

Related manuals for N5221BU-677

Brands by name

Popular brands

Keysight N5221BU-677, Installation Note

Search results

Summary of Contents for N5221BU-677

Reviews:

Related manuals for N5221BU-677

Brands by name

Popular brands