manualshive.com logo in svg

Keysight N5221BU-677, Installation Note

The Keysight N5221BU-677 is a high-quality network analyzer, designed for precision measurement and analysis. This product comes with an Installation Note and a comprehensive user manual, both available for free download on our website. Explore the full potential of your device with these essential resources at manualshive.com.

Share
Download
background image

Installation Note N5222-90129                                                                                                                                  13

Items Included in the Upgrade Kit

W30

RF cable, Front panel jumper

6

N5222-20091

W42

a

RF cable, A21 HMA26.5 to A22 splitter

1

N5222-20009

W43

a

RF cable, A22 splitter to A23 mixer brick

1

N5222-20007

W44

a

RF cable, A22 splitter to A24 mixer brick

1

N5222-20008

W48

RF cable, A33 reference mixer switch to A23 mixer brick (R1)

1

N5222-20101

W49

RF cable, REF 3 RCVR R3 IN to A24 mixer brick (R3)

1

N5222-20024

W50

RF cable, REF 4 RCVR R4 IN to A24 mixer brick (R4)

1

N5222-20027

W52

RF cable, A23 mixer brick (R1) to A20 IF multiplexer (P411)

1

N5242-60021

W53

RF cable, A23 mixer brick (R2) to A20 IF multiplexer (P412)

1

N5242-60022

W55

RF cable, A24 mixer brick (D) to A20 IF multiplexer (P801)

1

N5242-60024

W56

RF cable, A24 mixer brick (R4) to A20 IF multiplexer (P414) 

1

N5242-60019

W57

RF cable, A24 mixer brick (R3) to A20 IF multiplexer (P413)

1

N5242-60020

W58

RF cable, A24 mixer brick (C) to A20 IF multiplexer (P601)

1

N5242-60023

W60

RF cable, A20 IF multiplexer board P203 to A12 SPAM board (J2)

1

N5242-60013

W62

RF cable, A20 IF multiplexer board P603 to A12 SPAM board (J5)

1

N5242-60015

W75

RF cable, A26 port 3 receiver coupler to A35 port 3 source attenuator

1

N5222-20002

W76

RF cable, A35 port 3 source attenuator to front-panel Port 3 SOURCE OUT

1

N5222-20019

W79

RF cable, A27 port 4 receiver coupler to A36 port 4 source attenuator

1

N5222-20001

W80

RF cable, A36 port 4 source attenuator to front-panel Port 4 SOURCE OUT

1

N5222-20020

W89

RF cable, Port 3 RCVR C IN to A43 port 3 receiver attenuator

1

N5222-20021

W90

RF cable, A43 port 3 receiver attenuator to A24 mixer brick (C)

1

N5222-20006

W91

RF cable, Port 4 RCVR D IN to A44 port 4 receiver attenuator

1

N5222-20022

W92

RF cable, A44 rt 4 receiver attenuator to A24 mixer brick (D)

1

N5222-20026

W202

b

RF cable, A24 mixer brick (top connector) to A21 HMA25.6 A24 mixer brick (top 

connector)

1

N5222-20126

--

Ribbon cable, A19 test set motherboard J213 to A24 mixer brick (2)

1

N5242-60006

--

Ribbon cable, A19 test set motherboard J206 to A43 port 3 receiver attenuator

1

8121-0982 

--

Ribbon cable, A19 test set motherboard J207 to A44 port 4 receiver attenuator

1

8121-0982 

 

Table 2 

Contents of Upgrade Kit N5222-60129

Ref 

Desig.

Description

Qty

 Part Number

Summary of Contents for N5221BU-677























































Reviews:

No comments

Related manuals for N5221BU-677

Xaoc Devices HEL Operator'S Manual preview
HEL
Brand: Xaoc Devices Pages: 4
Thonk Eurorack DIY Kit Instructions Manual preview
Eurorack DIY Kit
Brand: Thonk Pages: 17
Patching Panda Vibrazum Manual preview
Vibrazum
Brand: Patching Panda Pages: 4
Norand Mono Quick Start Manual preview
Mono
Brand: Norand Pages: 23
Yamaha Clavinova CLP-870 Owner'S Manual preview
Clavinova CLP-870
Brand: Yamaha Pages: 132
SequentialSystems prophet-10 Operation Manual preview
prophet-10
Brand: SequentialSystems Pages: 113
Cyclone Analogic Bass Bot TT-303 Operation Manual preview
Bass Bot TT-303
Brand: Cyclone Analogic Pages: 24
Cyclone Analogic Bass Bot Operation Manual preview
Bass Bot
Brand: Cyclone Analogic Pages: 28

Brands by name

Popular brands

Load more brands