Keysight N5221BU-677 Page 7 Installation Note Download

Page: 7 / 54

Installation Note N5222-90129

Getting Prepared

Verify the Model/Version of HMA26.5 Installed

This upgrade kit contains components for use with PNA models using the

legacy HMA26.5 part number 5087-7765. If your PNA has the newer HMA26.5

part number N5240-60101 installed you may discard these parts:

— A22 splitter 5087-7139
— W42 N5222-20009
— W43 N5222-20007
— W44 N5222-20008

Figure 1

(If you have the legacy 5086-7765 HMA26.5, please discard the
N5245-20195 semi-rigid cables.

Refer to

Figure 1 on page 7

)

The new N5240-60101 HMA26.5 has the splitter integrated into the

assembly. Refer to

Figure 1 on page 7

Comparison of Legacy HMA26.5 (5087-7765) and New HMA26.5

(N5240-60101)

Downloading the Online PNA Service Guide

To view the online Service Guide for your PNA model number, use the following

steps:

1. Go to

www.keysight.com

2. In the Search box, enter the model number of the analyzer (Ex: N5242A)

and click

Search

3. Click

Technical Support

Manuals

4. Click

Service Manual

5. Click the service guide title to download the PDF file.

Summary of Contents for N5221BU-677























































Search results

Summary of Contents for N5221BU-677

Reviews:

Related manuals for N5221BU-677

Brands by name

Popular brands

Keysight N5221BU-677, Installation Note

Search results

Summary of Contents for N5221BU-677

Reviews:

Related manuals for N5221BU-677

Brands by name

Popular brands