Keysight E4356A Operating Manual Download Page 85

Page: 85 / 134

84 Language Dictionary

Command Syntax

[SOURce]:VOLTage[:LEVel][:IMMediate][AMPLitude] <NRf+>

[SOURce][:VOLTage[:LEVel]:TRIGgered[:AMPLitude] <NRf+>

Parameters

Table 7-1

Default Suffix

*RST Value

Table 7-1

Examples

VOLT 200

VOLTAGE:LEVEL 200 MA

VOLTAGE:LEVEL:IMMEDIATE:AMPLITUDE 2.5

VOLT:TRIG 20

VOLTAGE:LEVEL:TRIGGERED 20

Query Syntax

[SOURce]:VOLTage[:LEVel][:IMMediate][:AMPLitude]?

MAX

[SOURce]:VOLTage[:LEVel][:IMMediate][:AMPLitude]? MIN

[SOURce]:VOLTage[LEVel]:TRIGgered[:AMPLitude]?

[SOURce]:VOLTage[LEVel]:TRIGgered[:AMPLitude]? MAX

[SOURce]:VOLTage[:LEVel]:TRIGgered[:AMPLitude]? MIN

Returned Parameters

<NR3>

VOLT?

and

VOLT:TRIG?

return presently programmed

immediate and triggered levels. If not triggered level is programmed,

both returned values are the same.

VOLT? MAX

and

VOLT? MIN

return the maximum and

minimum programmable immediate voltage levels.

VOLT:TRIG? MAX

and

VOLT:TRIG? MIN

return the

maximum and minimum programmable triggered voltage levels.

Related Commands

For

VOLT

*SAV *RCL

*RST

For

VOLT:TRIG

ABOR VOLT *RST

VOLT:PROT

This command sets the overvoltage protection (OVP) level of the power supply. If the output voltage exceeds the OVP

level, then the power supply output is disabled and the Questionable Condition status register OV bit is set (see "Chapter 8 -

Status Reporting"). An overvoltage condition can be cleared with the

OUTP:PROT:CLE

command after the condition

that caused the OVP trip is removed. The OVP always trips with zero delay and is unaffected by the

OUTP:PROT:DEL

command.

Command Syntax

[SOURce]:VOLTage:PROTection[:LEVel] <NRf+>

*Alternate

Syntax

[SOURce]:VOLTage:PROTection:AMPLitude <NRf+>

Parameters

Table 7-1

Default Suffix

*RST Value

MAX

Examples

VOLT:PROT 21.5 VOLT:PROT:LEV MAX

VOLTAGE:PROTECTION:LEVEL 145E-1

Query Syntax

[SOURce]:VOLTage:PROTection[:LEVel]?

[SOURce]:VOLTage:PROTection [:LEVel]? MIN

[SOURce]:VOLTage:PROTection [:LEVel]? MAX

Returned Parameters

<NR3>

VOLT:PROT?

returns presently programmed

OVP level.

VOLT:PROT? MAX

and

VOLT:PROT? MIN

return the

maximum and minimum programmable OVP levels.

Related Commands

OUTP:PROT:CLE *RST *SAV *RCL

* Available to accommodate earlier power supply programs.

Summary of Contents for E4356A







































































































































Search results

Summary of Contents for E4356A

Reviews:

Related manuals for E4356A

Brands by name

Popular brands

Keysight E4356A, Operating Manual

Search results

Summary of Contents for E4356A

Reviews:

Related manuals for E4356A

Brands by name

Popular brands