Keysight E4356A Operating Manual Download Page 21

Page: 21 / 134

Installation

VXI

plug&play

Power Products

Instrument Drivers

VXI

plug&play

Power Products instrument drivers for Microsoft Windows 95 and Windows NT are now available on the

Web at

http://www.keysight.com/find/drivers

. These instrument drivers provide a high-level programming interface to

your Keysight Power Products instrument. VXI

plug&play

instrument drivers are an alternative to programming your

instrument with SCPI command strings. Because the instrument driver's function calls work together on top of the VISA

I/O library, a single instrument driver can be used with multiple application environments.

Supported Applications

System Requirements



Keysight VEE



Microsoft Visual BASIC



Microsoft Visual C/C++



Borland C/C++



National Instruments LabVIEW



National Instruments LabWindows/CVI

The VXI

plug&play

Power Products instrument driver

complies with the following:



Microsoft Windows 95



Microsoft Windows NT 4.0



HP VISA revision F.01.02



National Instruments VISA 1.1

Downloading and Installing the Driver

NOTE:

Before installing the VXI plug&play instrument driver, make sure that you have one of the supported

applications installed and running on your computer.

1. Access Keysight Technologies’ Web site at

http://www.keysight.com/find/drivers

2. Select the instrument for which you need the driver.

3. Click on the driver, either Windows 95 or Windows NT, and download the executable file to your pc.

4. Locate the file that you downloaded from the Web. From the

Start

menu select

Run

<path>:\agxxxx.exe - where

<path> is the directory path where the file is located, and agxxxx is the instrument driver that you downloaded .

5. Follow the directions on the screen to install the software. The default installation selections will work in most

cases. The readme.txt file contains product updates or corrections that are not documented in the on-line help. If

you decide to install this file, use any text editor to open and read it.

6. To use the VXI

plug&play

instrument driver, follow the directions in the VXI

plug&play

online help under

“Introduction to Programming”.

Accessing Online Help

A comprehensive online programming reference is provided with the driver. It describes how to get started using the

instrument driver with Keysight VEE, LabVIEW, and LabWindows. It includes complete descriptions of all function calls

as well as example programs in C/C++ and Visual BASIC.



To access the online help when you have chosen the default Vxipnp start folder, click on the Start button and select

Programs | Vxipnp | Agxxxx Help (32-bit).

- where Agxxxx is the instrument driver.

Summary of Contents for E4356A







































































































































Search results

Summary of Contents for E4356A

Reviews:

Related manuals for E4356A

Brands by name

Popular brands

Keysight E4356A, Operating Manual

Search results

Summary of Contents for E4356A

Reviews:

Related manuals for E4356A

Brands by name

Popular brands