Keysight E4356A Operating Manual Download Page 25

Page: 25 / 134

Turn-On Checkout

Press

Dis

annunciator turns on.

Press

You have disabled the overcurrent protection circuit. The

OCP

annunciator turns off.

Press

(

)**

You have cleared the overcurrent protection circuit. The

Prot

annunciator turns off.

Press

Dis

turns off and

turns on. The output current is restored.

If you have a shorting wire of sufficient capacity,

you may continue testing up to the maximum rated current of the power

supply (see "Performance Specifications"). When finished, go to the next step.

Press

Dis

turns on and output current drops to zero.

Turn off the power supply and remove the short from the output terminals.

Checking The Save And Recall Functions

Keysight E4356A power supplies have five nonvolatile memory storage locations (0 through 4). Proceed as follows:



Make certain that the output is on (

Dis

annunciator is off).



Set the voltage output to 5 by pressing



Save this value to location 1 by pressing



Return the output voltage to 0 by pressing

(This step is based on the fact that a newly shipped power

supply has the

*RST

parameters stored in location 0 (see "Chapter 5 - Front Panel" for more information).



Press

and notice that the output voltage returns to the value stored in location 1.

Determining The GPIB Address

When the power supply is turned on, the display shows ADDR n, where n is the power supply GPIB address. Any time you

want to see the address, press

The display will indicate

ADDR 5

, which is the factory default. If the address has been changed, then a different number

will appear (see “Setting the GPIB Address” in “Chapter 5 - Front Panel”).

In Case Of Trouble

Line Fuse

If the power supply appears "dead" with a blank display and the fan not running, first check your power source to be certain

line voltage is being supplied to the power supply. If the power source is normal, the power supply line fuse may be

defective. If the unit has a defective fuse, replace it only once. If it fails again, investigate the reason for the failure. Proceed

as follows:

Hazardous voltage can remain inside the power supply even after it has been turned off. Fuse

replacement should be done only by qualified electronics personnel.

Summary of Contents for E4356A







































































































































Search results

Summary of Contents for E4356A

Reviews:

Related manuals for E4356A

Brands by name

Popular brands

Keysight E4356A, Operating Manual

Search results

Summary of Contents for E4356A

Reviews:

Related manuals for E4356A

Brands by name

Popular brands