Keysight Technologies N9000-90032 Installation Note Download Page 4

Page: 4 / 14

Installation Note

N9000-90032

Option T03, T06 - Tracking Generator Installation Kit

Installation Procedure

This installation note is part of an upgrade kit that provides all of the parts and instructions needed to
install the tracking generator board assembly in an Agilent N9000A CXA Signal Analyzer.

Contents

Tools Required

❏

Torx Driver T-10

❏

Torx Driver T-20

❏

5/16-inch torque wrench

❏

Agilent Calibration and Adjustment Software, N7814A

❏

Test equipment and computer supported by the X-series Performance Tests and Adjustment
Software

❏

Microsoft Windows based personal computer with internet access and USB port

❏

USB storage device >2GB free memory

Quantity

Description

Agilent Part Number

Tracking Generator Assembly

N9000-65402

RF Input Connector Assembly

N9000-60032

EMI O-ring Shielding

8160-1637

Cable Assembly, SMA TG-RF, 2

N9000-20104

Cable Assembly, SMA TG-RF, Bridge

N9000-20105

Cable Assembly, SMA TG-RF, 1

N9000-20106

Cable Assembly, MMCX TG-LO

N9000-20107

Cable Assembly, SMA TG Out

N9000-20109

Overlay

N9000-80100

Screw M3*0.5 (8 mm)

0515-0372

Entitlement Certificate

5964-5178

Entitlement Certificate Envelope

5967-7169

Installation Note

This note

Summary of Contents for N9000-90032















Search results

Summary of Contents for N9000-90032

Reviews:

Related manuals for N9000-90032

Brands by name

Popular brands

Keysight Technologies N9000-90032, Installation Note

Search results

Summary of Contents for N9000-90032

Reviews:

Related manuals for N9000-90032

Brands by name

Popular brands