background image

Mähraupe   HyCut 

Safety 

DE 

 
2021-01-27 

11 / 65 

 

2.3 

Intended use 

  WARNING 

 

Risk of injury / risk of environmental damage caused by improper use of the 
machine! 

If the machine is used improperly, it may result in injury and can cause 
environmental and material damage (to the machine or system)! 
• 

The HyCut tracked mower has been designed for usual or common 
mowing applications in the agricultural and forestry sectors, such as for the 
maintenance of green spaces and parks. 

• 

Any use going beyond this is deemed to be improper use. The 
manufacturer does not assume liability for damage arising from such use. 
The operator bears the sole risk. 

• 

Adhering to the intended use includes complying with the manufacturer’s 
operating, maintenance and repair specifications. 

• 

The HyCut tracked mower may only be used, maintained and repaired by 
people who are familiar with it and who have been instructed about the 
associated hazards. 

• 

All applicable accident prevention regulations and any applicable general 
regulations regarding safety and occupational health must be observed 
and followed. 

• 

Any damages caused as a result of unauthorised modifications made to 
the machine will be excluded from the manufacturer’s liability. 

 

 

2.4 

Work areas and danger zones 

 

Fig. 1: Danger zones (view from above) 

Summary of Contents for B00108


































































Reviews: