Kenwood TK-5220 Instruction Manual Download Page 5

Page: 5 / 44

recauTions

• Do not charge the transcever and battery pack when they are wet.
• Ensure that there are no metallc tems located between the

transcever and the battery pack.

• Do not use optons not specfed by

Kenwood

• If the de-cast chasss or other transcever part s damaged, do not

touch the damaged parts.

• If a headset or headphone s connected to the transcever, reduce

the transcever volume. Pay attenton to the volume level when

turnng the squelch off.

• Do not place the mcrophone cable around your neck whle near

machnery that may catch the cable.

•  Do not place the transcever on unstable surfaces.
•  Ensure that the end of the antenna does not touch your eyes.
•  When the transcever s used for transmsson for many hours, the

radator and chasss wll become hot. Do not touch these locatons

when replacng the battery pack.

• Always swtch the transcever power off before nstallng optonal

accessores.

• The charger s the devce that dsconnects the unt from the AC

mans lne. The AC plug should be readly accessble.

Summary of Contents for TK-5220













































Search results

Summary of Contents for TK-5220

Reviews:

Related manuals for TK-5220

Brands by name

Popular brands

Kenwood TK-5220, Instruction Manual

Search results

Summary of Contents for TK-5220

Reviews:

Related manuals for TK-5220

Brands by name

Popular brands