Kenwood TK-5220 Instruction Manual Download Page 39

Page: 39 / 44

Attery

Aver

The Battery Saver decreases the amount of power used when

a signal is not being received and no operations are being

performed.

ock

Press the key programmed as

Key Lock

to lock and unlock the

transceiver keys.

• The following keys still function when Key Lock is activated:

Emergency, Backlight, Monitor, Monitor Momentary, Squelch Off,

Squelch Off Momentary, Speaker Attenuation, Function, Key Lock,

PTT

Attery

Arning

Low Battery Warning alerts you when the battery needs to be

recharged. Your dealer can set an alert tone to sound and the

LED indicator to blink red when the battery power is low. The

battery power icon displays the battery power remaining, as

illustrated below.

High

Sufficient

Low

Very low

When the battery power is very low, recharge or replace the

battery pack.

ignAl

trength

ndicAtor

The signal strength indicator displays the strength of received

calls.

Strong

Sufficient

Weak

Very weak

No icon appears when no signal is available.

Summary of Contents for TK-5220













































Search results

Summary of Contents for TK-5220

Reviews:

Related manuals for TK-5220

Brands by name

Popular brands

Kenwood TK-5220, Instruction Manual

Search results

Summary of Contents for TK-5220

Reviews:

Related manuals for TK-5220

Brands by name

Popular brands