Kenwood TK-5220 Instruction Manual Download Page 40

Page: 40 / 44

ompAnder

If programmed by your dealer for a channel, the compander

will remove excessive noise from transmitted signals, to

provide higher clarity of signals.

uSy

hAnnel

ockout

(Bcl)

If BCL is set up by your dealer, you will be unable to transmit if

the channel is already in use. Use a different channel or wait

until the channel becomes free.
If BCL Override has been programmed, you can transmit over

the current signal:

Press and hold the

PTT

switch.

• If the channel is already in use, a warning tone will sound.

Quickly release and then press the

PTT

switch again.

Speak into the transceiver as you would during a normal

call.

ptt id

PTT ID is the transceiver unique ID code which is sent each

time the

PTT

switch is pressed and/or released.

Note:

PTT ID can be made only in analog operation.

Summary of Contents for TK-5220













































Search results

Summary of Contents for TK-5220

Reviews:

Related manuals for TK-5220

Brands by name

Popular brands

Kenwood TK-5220, Instruction Manual

Search results

Summary of Contents for TK-5220

Reviews:

Related manuals for TK-5220

Brands by name

Popular brands