TK-2317
9
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or elec-
tromagnetics are being performed at the workbench.
• Wireless clone mode can be used ONLY by the autho-
rized service personnel.
• The wireless clone mode setting must be confi gured as
“Disable” before being delivered to the end-user.
• To wireless clone, replace the antenna from both the
source transceiver and the target transceiver with a dum-
my load.
• The transmit output power is automatically set to Low in
Clone mode.
4-4. Adding the Data Password
If the Data password is set to the transceiver, you must
enter the password to activate a clone mode. The maximum
length of the password is 6 digits.
The following describes how to enter the password.
1. Press and hold the [<B] key for 2 seconds while turning
the transceiver power on.
2. “CLN.LOCK.R”(When the Read authorization password
is set to the transceiver.) / “CLN.LOCK.W” (When the
Overwrite password is set to the transceiver.) is displayed
on the LCD.
3. If the [selector] knob is rotated while “CLN.LOCK.R”/
“CLN.LOCK.W” is displayed, the number (0 to 9) fl ashes
on the LCD.
When you press the [C>] key, the currently selected num-
ber is determined.
If you press the [A] key, the least digit of the password is
deleted.
If you press the [S] key after entering the password in this
procedure, “FRQTBL 1” is displayed if the entered pass-
word is correct.
If the password is incorrect, “CLN.LOCK.R”/ “CLN.LOCK.
W” is redisplayed. (with error tone)
• Clone frequency table
No.
Operating frequency 136~174 (MHz)
1
136.000
2
138.000
3
140.000
4
142.000
5
144.000
6
146.000
7
148.000
8
150.000
9
152.000
10
154.000
11
156.000
12
158.000
13
160.000
14
162.000
15
164.000
16
166.000
17
168.000
18
170.000
19
172.000
20
174.000
REALIGNMENT /
模式组合
•
无复制模式只可以由授权的服务人员使用。
•
在向最终用户交货之前，无复制模式必须设置为“禁用”
。
•
无复制时，取下主手持对讲机和子手持对讲机的天线并装
上假负载。
•
在复制模式，手持对讲机输出功率自动地被设定为低功率。
4-4. 增加数据密码
如果数据密码被设定于手持对讲机，则您必须先输入密码
才能启动复制模式。密码的最大长度为 6 位数字。
输入密码的方法说明如下。
1. 打开手持对讲机电源的同时，持续按 [<B] 键 2 秒。
2.“CLN.LOCK.R”( 当读取授权密码被设定到手持对讲机时 )
／“CLN.LOCK.W”( 重写密码被设定到手持对讲机时 ) 被
显示在 LCD。
3. 在“CLN.LOCK.R”／“CLN.LOCK.W”被显示时，如果 [ 选
择器 ] 旋钮被转动，在 LCD 上会闪烁出数字 (0 ～ 9)。
当您按了 [C>] 键，通常被选择的数字将被确定。
如果您按了 [A] 键，密码的最小位数字将被删除。
在此程序中输入了密码，并且被输入的密码正确，如果您
按了 [S] 键，则显示出“FRQTBL 1”
。
如果密码错误，
则继续显示“CLN.LOCK.R”／“CLN.LOCK.W”
。
( 发出错误音 )
•
复制频率表
号码
操作频率 136 ～ 174 (MHz)
1
136.000
2
138.000
3
140.000
4
142.000
5
144.000
6
146.000
7
148.000
8
150.000
9
152.000
10
154.000
11
156.000
12
158.000
13
160.000
14
162.000
15
164.000
16
166.000
17
168.000
18
170.000
19
172.000
20
174.000
