Kenwood NEXEDGE NX-410 Instruction Manual Download | Manualshive

Page: 6 / 44

background image

iii

P

RECAUTIONS

•

Do not charge the transceiver and battery pack when they are wet.

•

Ensure that there are no metallic items located between the
transceiver and the battery pack.

•

Do not use options not specified by

Kenwood

.

•

If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts.

•

If a headset or headphone is connected to the transceiver, reduce
the transceiver volume. Pay attention to the volume level when
turning the squelch off.

•

Do not place the microphone cable around your neck while near
machinery that may catch the cable.

•

Do not place the transceiver on unstable surfaces.

•

Ensure that the end of the antenna does not touch your eyes.

•

When the transceiver is used for transmission for many hours, the
radiator and chassis will become hot. Do not touch these locations
when replacing the battery pack.

•

Always switch the transceiver power off before installing optional
accessories.

•

The charger is the device that disconnects the unit from the AC
mains line. The AC plug should be readily accessible.

«
...
4
5
6
7
8
...
»

Summary of Contents for NEXEDGE NX-410













































Reviews:

No comments

Related manuals for NEXEDGE NX-410

Brand: Takstar Pages: 24

Brand: Cables to Go Pages: 5

Brand: Labom Pages: 6

Brand: Labom Pages: 28

Brand: unicore Pages: 7

Brand: Yamaha Pages: 8

Brand: Yaesu Pages: 5

Brand: Sennheiser Pages: 32

Brand: M-system Pages: 4

Brand: ferroamp Pages: 10

Brand: Mhouse Pages: 2

Brand: Camille Bauer Pages: 40

Brand: Radio Corporation Pty Pages: 75

Brand: AAS Pages: 4

Brand: Allmatic Pages: 10

Brand: Teac Pages: 40

Brand: BluStream Pages: 4

Brand: LD Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands