Kenwood NEXEDGE NX-410 Instruction Manual Download

Page: 37 / 44

■

Optional Signaling

Your dealer may also program several types of optional
signaling for your transceiver channels.

DTMF Signaling:

DTMF Signaling opens the squelch only

when the transceiver receives a call containing a matching
DTMF code.

FleetSync

Signaling:

Refer to “S

ELCALL

ELECTIVE

ALLING

)” on page 17.

NXDN ID Signaling:

NXDN ID is an optional signaling

system available only for digital communications.

OICE

PERATED

RANSMISSION

(VOX)

VOX can be activated or deactivated by your dealer. VOX
operation allows you to transmit hands-free.

Note:

To operate VOX, you must use an optional KHS-11, KHS-14,

KHS-15-BH, or KHS-15-OH headset.

■

VOX Gain Level

Connect the headset to the transceiver.

Press the key programmed as

VOX

•

The current VOX Gain level appears on the display.

Press /

to increase or decrease the VOX Gain

level.

•

The VOX Gain can be adjusted from levels 1 to 10.

While adjusting the level, speak into the headset

microphone to test the sensitivity level. (Your voice is
not trasmitted during this test procedure.)

•

When sound is recognized, the LED lights orange.

Press to save the setting.

Summary of Contents for NEXEDGE NX-410













































Search results

Summary of Contents for NEXEDGE NX-410

Reviews:

Related manuals for NEXEDGE NX-410

Brands by name

Popular brands

Kenwood NEXEDGE NX-410, Instruction Manual

Search results

Summary of Contents for NEXEDGE NX-410

Reviews:

Related manuals for NEXEDGE NX-410

Brands by name

Popular brands