Kenwood KAF-S500, Instruction Manual

Page: 16 / 37

16
EN
!
Press the SET UP key again to accept the setting.
• The subw oofer remix setting indication ” REM IX” appears.
• If subw oofer is turned off, subw oofer re-mix setting is not visible.
@
Use the TRIM % / fi keys to select the appropriate subw oofer
re-mix setting.
1
REM IX ON : Subw oofer re-m ix setting m ode to
the amplifier is ON.
2
REM IX OFF : Subw oofer re-m ix setting m ode to
the amplifier is OFF.
When “REM IX ON” is selected, bass sound of other channel
w ill be added into Subw oofer or bass sound of Subw oofer
w ill be added int o ot her channel t o increase deep bass
performance.
#
Press the SET UP key again to return to the
2
.
• The receiver enters the speaker volume level adjustment mode.
• In steps
5
and
6
, indications appear only for the selected
channels of the speakers that require adjusting.
5
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
1
Press the SET UP key and then use the TRIM % / fi keys to
select TEST TONE.
2
Press the SET UP key for the follow ing displays:
The selection of AUTO or M ANUAL is done by the TRIM % / fi
keys.
1
AUTO
2
M ANUAL
3
Press the SET UP key again to begin TEST TONE.
Use the TRIM % / fi keys to adjust the volume level of the test
tone output from the speaker channel to be adjusted.
For AUTO selection, the first test tone is heard from the front left
speaker for 3 seconds. The next test tone is heard from the
speakers in the follow ing sequence for 3 seconds each.
The channel indication blinks w hile the test tone is being output.
• If you change the volume level settings for the speakers w hile
listening to music, the settings referred to on this page are also
changed.
• If the speaker setting selects are OFF, the speaker level settings
are reset.
For “M ANUAL” selection, press the FRONT, CENTER, REAR
or SW keys to select the speaker channel and then adjust the
volume level by pressing TRIM
% / fi keys.
Preparing for surround sound
6
Use the TRIM % / fi keys to select the appropriate center
speaker setting.
If you selected “LRG” as the front speakers setting,
1
CNTR NM L : An average size center speaker is
connected to the amplifier.
2
CNTR LRG : A large center speaker is connected
to the amplifier.
3
CNTR OFF : Center speaker setting mode to the
amplifier is OFF.
If you selected “NM L” as the front speakers setting,
1
CNTR ON : Center speaker setting mode to the
receiver is ON.
2
CNTR OFF : Center speaker setting mode to the
receiver is OFF.
7
Press the SET UP key again to accept the setting.
• The surround speaker indication “ SURR” appears.
8
Use the TRIM % / fi keys to select the appropriate surround
speaker setting.
If you selected “LRG” as the center speaker setting,
1
SURR NM L : Average size surround speakers are
connected to the amplifier.
2
SURR LRG : L ar g e s u r r o u n d s p e ak e r s ar e
connected to the amplifier.
3
SURR OFF : Surround speaker setting m ode to
the amplifier is OFF.
If you selected other than “LRG” as the center speaker setting,
1
SURR ON : Surround speaker setting mode to the
amplifier is ON.
2
SURR OFF : Surround speaker setting mode to the
amplifier is OFF.
• When the setting “ SURR OFF” is selected, by pressing the SET
UP key in step
9
the procedure skips to step
@
. But if “ SW
OFF” is selected, press the SET UP key to skip to step 5 .
9
Press the SET UP key again to accept the setting.
• The back surround speaker setting indication “ BS” appears.
0
Use the TRIM % / fi keys to select appropriate surround back
speaker setting.
If you selected “LRG” as the surround speaker setting,
1
BS NM L : Average size back surround speaker is
connected to the amplifier.
2
BS LRG : Large back surround speaker is con-
nected to the amplifier.
3
BS OFF : Back surround speaker setting mode to
the amplifier is OFF.
If you selected “NM L” as the surround speaker setting,
1
BS NM L : Back surround speaker setting mode
to the amplifier is ON.
2
BS OFF : Back surround speaker setting mode
to the amplifier is OFF.
MUTE DOLBY DEX NEO:6 DSP TS DIGITAL ST.
AUTO
L
LFE SW
C R
DOLBY PL
II
DTS -ES AAC
DISCRETE
MATRIX 6.1
ACTIVE EQ.
LS S BS RS
L C R RS
BS LS SW
MUTE DOLBY DEX NEO:6 DSP TS DIGITAL ST.
AUTO
L
LFE SW
C R
DOLBY PL
II
DTS -ES AAC
DISCRETE
MATRIX 6.1
ACTIVE EQ.
LS S BS RS
MUTE DOLBY DEX NEO:6 DSP TS DIGITAL ST.
AUTO
L
LFE SW
C R
DOLBY PL II
DTS -ES AAC
DISCRETE
MATRIX 6.1
ACTIVE EQ.
LS S BS RS
名称未設定- 1 0