background image

WARNING

IMPORTANT

1. To protect against electric shock, do not immerse cord or plugs in water or other liquid.

Cleaning the Lens

1. Prior to cleaning, make sure the light switch is in the “OFF” position and the light plug is 
    disconnected from the power supply.

2. Do not clean the glass lens when warm.  Allow to cool before cleaning.  Sudden change in 
    temperature may cause cracking of the glass lens.
3. Use a damp towel to clean the surface of the glass lens.

4. Allow the lens to dry before reconnecting the light plug to the power supply and turning the 
    light switch to the “ON” position.

 •  Since 1971 the National Electric Code (NEC) has required Ground Fault Interrupter devices on all outdoor 
    circuits.

 •  If your residence was built before 1971, check with a qualified electrician to determine if a Ground Fault 

    Interrupter protector exists.

 •  Do not use this appliance if the circuit does not have GFI protection.

 •  Do not plug this appliance into an indoor circuit.

2. Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.

3. Do not operate grill with a damaged cord, plug, or after the appliance malfunctions or has been damaged in any 
    manner.
4. Do not let the cord hang over the edge of a table or touch hot surfaces.

5. Do not use an outdoor cooking gas appliance for purposes other than intended.

6. When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.

7. Use only a Ground Fault Interrupter(GFI) protected circuit with this outdoor cooking gas appliance.

8. Never remove the grounding plug or use with an adapter of 2 prongs.

9. Use only extension cords with a 3 prong grounding plug, rated for the power  of the equipment, and approved for 
    outdoor use with a W-A marking.

12 • 464224011

Summary of Contents for 415.1664901





































Reviews: