background image

4 • 464224011

USE  AND CARE

OPD Hand Wheel

LP (Liquefied Petroleum Gas)

• LP gas is nontoxic, odorless and colorless when produced. 

For Your Safety

, LP gas has been given an odor (similar to 

rotten cabbage) so that it can be smelled. 

• LP gas is highly flammable and may ignite unexpectedly 

when mixed with air.

LP Tank Filling

• Use only licensed and experienced dealers.

• LP dealer 

must purge new tank

 before filling.

 Dealer should 

NEVER

 

fill LP Tank more than 80% of LP Tank

 

volume. Volume of propane in tank will vary by temperature.

• A frosty regulator indicates gas overfill. Immediately close 

LP Tank valve and call local LP gas dealer for assistance.

• Do not release liquid propane (LP) gas into the atmosphere. 

This is a hazardous practice.

• To remove gas from LP Tank, contact an LP dealer or call a 

local fire department for assistance. Check the telephone 
directory under “Gas Companies” for nearest certified LP 
dealers.

LP Tank   

• The LP Tank used with your grill must meet the following 

requirements:

• Use LP Tanks only with these required measurements: 12" 

(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) 
capacity maximum.

• LP Tanks must be constructed and marked in accordance 

with specifications for LP Tanks of the U.S. Department of 
Transportation (DOT) or for Canada, CAN/CSA-B339, tanks, 
spheres and tubes for transportation of dangerous goods. 
Transport Canada (TC). See LP Tank collar for marking.

• LP Tank valve must have:

• Type 1 outlet compatible with 

regulator or grill.

• Safety relief valve.

• UL listed Overfill Protection 

Device (OPD). This OPD safety

feature is identified by a unique triangular hand wheel.

 

Use only LP Tanks equipped with this type of valve.

• LP Tank must be arranged for vapor withdrawal and include 

collar to protect LP Tank valve. Always keep LP Tanks in 
upright position during use, transit or storage.

LP Tank in upright position for vapor withdrawal

 

LP Tank Removal, Transport And Storage

LP Tank Valve

Retainer Strap

Safety Cap

• A disconnected LP tank in storage or being transported must 

have a safety cap installed (as shown). Do not store an LP 
tank in enclosed spaces such as a carport, garage, porch, 
covered patio or other building. Never leave an LP tank 
inside a vehicle which may become overheated by the sun.

• Do not store an LP tank in an area where children play.

NEVER store a spare LP cylinder under or near the 
appliance or in an enclosed area. 

Never fill a cylinder beyond 80% full.

If the information in the two points above is not 
followed exactly, a fire causing death or serious 
injury may occur. 

An overfilled or improperly stored cylinder is a 
hazard due to possible gas release from the safety 
relief valve.  This could cause an intense fire with 
risk of property damage, serious injury or death.

If you see, smell or hear gas escaping, immediately 
get away from the LP cylinder and appliance and  
call your fire department.

DANGER

• Turn OFF all control knobs and LP tank valve. Turn coupling 

nut counterclockwise by hand only - do not use tools to 
disconnect. Lift LP tank wire upward off of LP tank collar, 
then lift LP tank up and off of support bracket. Install 
safety cap onto LP tank valve. Always use cap and strap 
supplied with valve.

Failure to use safety cap as directed may result in serious 
personal injury and/or property damage. 

Summary of Contents for 415.1664901





































Reviews: