background image

Kendrion Kuhnke Automation GmbH 

Construction and Functionality 

 

Vico MT

 (

E 863 GB

) 

33

 

01/10/2021 

 

4.3  Putting into Service 

 General Start-up Information 

 

 

CAUTION 

Risk of burns 

The surface of the device may become very hot. Unprotected contact causes a risk of burning 
yourself. 

  Avoid direct contact with the unit in operation. Put on suitable safety gloves before 

touching the unit. 

 

 

NOTE 

Pull of the protective film to the side 

 

The protective film on the front removes easily by pulling it off to the side.

 

 

Touch screen operation 

Operate the touch screen objects by touching them with your finger or a suitable stylus. 

 

 

NOTE 

Damage to the touch screen by pointed or hard objects 

Destruction of front 

Do not use pointed or hard objects to operate the touch screen. 

  Avoid sudden or impact-like touch screen contact by hard objects because this may 

destroy the touch screen. Touch the screen of Touch with your finger or the stylus only. 

 

 Start-up Prerequisites 

 

Functional earth is connected. 

 

All cables are attached properly. 

 

Power is supplied to the unit. 

 Turning on the Unit 

Connect the unit to the power supply. 

The unit does not have an On/Off switch. Instead, it will start up automatically when you turn on the power 
supply. The user interface of the operating system displays after the boot-up routine. 

 Turning off the Unit 

You may directly unplug the unit from the power supply. 

Summary of Contents for Vico MT 1027























































Reviews: