background image

TABLE OF CONTENTS

Indications .......................................................................................................................... 1
Contraindications ................................................................................................................ 1
Cautions .............................................................................................................................. 1
Explanation of Symbols Used ................................................................................................ 2
Front Panel Display .............................................................................................................. 2

Section I - General Operating Instructions ............................................................................. 3

Set up .............................................................................................................................................................................3

Start-up .........................................................................................................................................................................3

Garment Configuration & Detection .............................................................................................................................3

Normal Operation ..........................................................................................................................................................4

Pressure Settings ...........................................................................................................................................................4

Vascular Refill Detection ...............................................................................................................................................4

Garment Compatibility ..................................................................................................................................................4

Tubing Set Compatibility ...............................................................................................................................................4

Portable Controller Configuration .................................................................................................................................4

Section II - Battery Operation ............................................................................................... 4

Battery Indicators Status  ..............................................................................................................................................5

Charging the Battery .....................................................................................................................................................5

Battery Warnings ...........................................................................................................................................................6

Section III - Fault Conditions and Troubleshooting ................................................................. 6

Watchdog Circuit ...........................................................................................................................................................6

Section IV - Service and Maintenance .................................................................................... 8

Introduction ...................................................................................................................................................................8

Warranty and Factory Service .......................................................................................................................................8

Fan Screen and Ventilation ............................................................................................................................................9

Fuses ..............................................................................................................................................................................9

Electrical Safety .............................................................................................................................................................9

Suggested Preventative Maintenance Schedule ..........................................................................................................9

Cleaning ...................................................................................................................................................................... 10

Electrical/Electronics Description ............................................................................................................................... 10

Pneumatic Operation Description .............................................................................................................................. 10

Section V - Test Methods and Calibration ............................................................................. 10

Test Mode 01 - Burn-In .............................................................................................................................................. 10

Test Mode Look up Chart ........................................................................................................................................... 11

Test Mode 02 - General Function Test ........................................................................................................................ 11

Test Mode 03 - Pressure Transducer Calibration ........................................................................................................ 11

Test Mode 04 - Pressure Transducer Calibration Verification ..................................................................................... 11

Summary of Contents for SCD EXPRESS

























Reviews: