background image

EN-15

Section VII - Specifi cations

SCD EXPRESS Compression System

Safety Standards

 

Built to UL60601-1, CSA-C22.2 No. 601.1-M90, EN60601-1, and IEC 60601-1-2  Standards

 

UL Classified File # E189131

UL Device Classification

 

Class I Equipment

Internally Powered, Portable

Type BF Applied Parts

Not AP or APG Equipments

Mode of Operation

 

Continuous

Ingress of Water Protection

Ordinary, IPX0 (IEC 529)

Compression Type

 

Leg Sleeves:  Sequential, Gradient

 

Foot Cuffs:   Uniform

Compression Cycle

 

Leg Sleeves:   11 Seconds Compression

 

Foot Cuffs:   5 Seconds Compression

 

Decompression time based upon Vascular Refill Detection measurement

Set Pressure

 

Leg Sleeves:   45 mmHg

 

Foot Cuffs:   130 mmHg

Bed Hook

 

Yes (Optional)

Bed Hook

Bed Hook

Power Cord Storage

 

Yes

Audible/Visual Alarms

Low Pressure, High Pressure, Internal Electronics Malfunction

Power Cord

Hospital Grade Plug

Controller Dimensions:

Height:  

6.2 inches (15.8 cm)

 

Width: 

7.0 inches (17.8 cm)

 

Depth: 

4.5 inches (11.4 cm)

Controller Weight

 

3.5 lbs. (1.6 kg)

Power Requirements

 

100-240 VAC, 50VA, 50/60 Hz

Battery

 

16.4 V, 2000mAhr, Lithium Ion (Optional) 

 

Run Time:    6-8 hours

 

Charge Time:   4 hours (charging only)

Shoulder Strap

 

Yes (Optional)

Shipping Unit

 

Each

Shipping Case Dimensions

Height:  

11.6 inches (29.4 cm)

 

Width: 

9.0 inches (22.8 cm

)

Depth:

11.4 inches (28.9 cm)

Shipping Weight

7 lbs. 6 oz. (3.45 kg)

Tubing Set

Included, set of two individual assemblies

Operation & Service Manual 

Included

Transport & Storage

0°C (32°F) to 50° C (122°F)

 

If the user suspects that the environment conditions

 

for transport and storage have been exceeded, return 

 

the unit for service.

Summary of Contents for SCD EXPRESS

























Reviews: