background image

8    general installation of solar collectors  

Kelvinator solar hot water systems

10-15mm

from horizontal

inlet

20-30mm

from horizontal

30-45mm

from horizontal

horizontal

collector rail

outlet

Note: The solar collectors (both flat panel and evacuated 

tube) must be installed at an angle from the horizontal. 

This is to ensure that any air in the system will travel to 

the air vent valve located on the outlet connection of the 

collectors.

The distance between the end of the collector rail at the 

outlet side of the solar collectors and the horizontal must be:

 

10 - 15 mm (for one solar collector)

 

20 - 30 mm (for two solar collectors)

 

30 - 45 mm (for three solar collectors)

If the roof material is uneven where the collectors are to be 

installed, then it may be necessary to add an additional 10 

mm to the above distances for each collector.

Space requirements

A

B

C

C

D

Space and load bearing requirements for evacuated  
tube collectors

No. of 
collectors

Dimension  
A (mm)

Dimension  
B (mm)

Weight when 
full (approx.)

1

1400

1640

47kg

2

2800

1640

94kg

3

4200

1640

141kg

Dimensions C and D

•  when determining the location for the collector ensure 

that there is adequate space available for the water 
connections and the fixing of the mounting kit.

A

B

C

C

D

Space and load bearing requirements for flat  
panel collectors

No. of 
collectors

Dimension  
A (mm)

Dimension 
B (mm)

Weight when 
full (approx.)

1

1025

2050

45kg

2

2050

2050

90kg

3

3075

2050

135kg

General installation of solar collectors

Summary of Contents for KCT45036A

































Reviews: